Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: CRJarvis

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. it was a job to do with out taking off the table.

    it was a job to do with out taking off the table.
  2. 329353 busted it had not used it in a wile and...

    329353 busted it had not used it in a wile and after a few passes it went. so stopped by a few bearing places in town and found this. 329354the PowerGrip 450H100 was just right. cut it and a hell of...
  3. just busted the belt on it last night anyone have...

    just busted the belt on it last night anyone have ideas on how to install it. i looking at trying not to take it all apart to do it.
    picked up a belt that will work will post info and photos as i...
  4. ok looking for the 3 jaw chuck installation help....

    ok looking for the 3 jaw chuck installation help. like what torque specks do you use. will be looking up the bolts to see what they are.
  5. an old machinist has some cool stuff trying to...

    an old machinist has some cool stuff trying to work out a deal with him for a lathe and saw some of the stuff he has. he is not able to get up and around after a heart attack.
  6. Lincoln Electric Power MIG 350MP Multi-Process Welder Model# K2403-2 with a

    MK Python push pull system set up on this welder
    not sure if you have seen this Welder in action but it seems to be able to do it all.
    ...
  7. was hoping this would turn 1 phase in to 3 phase....

    was hoping this would turn 1 phase in to 3 phase. (but the way the plate was reading it looked to be going the other way.)
    but it looks like it was made to turn 3 phase 480 Voltage in to 3 phase 208...
  8. what is this "Acme Transformer" what does it do and what is it used for?

    Large General Purpose Transformer
    Catalog No T-1A-53313-3S
    229808
    i think i have an idea.
  9. so after setting it up and getting it running...

    so after setting it up and getting it running like it should on the Roto Phase,
    i will might go back and give it a try again ( seeing i know how it should work and sound )
    but for anyone else that...
  10. ok so i converted it back and hooked it up to my...

    ok so i converted it back and hooked it up to my Roto Phase and still i get to weld for about 3 sec and then it stops the arc. but the wire keeps feeding any ideas on what this problem is?
    found a...
  11. ok so Miller sent me the left out pages that are...

    ok so Miller sent me the left out pages that are no longer in the Manual.
    this is how mine is before i moved any wires.
    228744

    228745

    i now have put all the wires back like Originally...
  12. it welds but the middle coil gets hot. and did...

    it welds but the middle coil gets hot. and did not do much welding so i would say this setup is not working.
    maybe if i flipped it back over and tried it. but i think my Capacitor is to big.
    ...
  13. 1st test of setup will test it again with Coil #2...

    1st test of setup will test it again with Coil #2 running the other way. (by flipping the wire on the Front of RB#4 and RB#5)


    https://www.facebook.com/CRJarvis/videos/10214888390315159/


    Now...
  14. more on Caps and the 90' phase shift. AC...

    more on Caps and the 90' phase shift. AC Capacitor Circuits | Reactance And Impedance -- Capacitive | Electronics Textbook
  15. 228231 looked up the manual:Miller CP-200...

    228231

    looked up the manual:Miller CP-200 208/230v serial # HH025651
    Serial Numbers: HG044019 through HK229133 (ours is serial # HH025651)
    Owners Manual: English

    228232228233
    this is from...
  16. 228229 this Photo is missing the info i need...

    228229
    this Photo is missing the info i need below hope someone can help me out with it.

    there is a few things i not sure about the size of the ‘MOTOR RUN’ type capacitors of 60 microfarad (uF),...
  17. the only wires you have to move. 1. take apart...

    the only wires you have to move.
    1. take apart the the Coils (CCW)
    hook CCW#1 with BC#3 that was on the back of the RB#7. Leave the Fan wire attached to RB#7 it has 110V going to it. (in this...
  18. The back side of the switch on the left of it the...

    The back side of the switch on the left of it the
    A
    B
    C
    should be
    C
    B
    A

    227702
  19. 227701 so looking at what was said and looking...

    227701
    so looking at what was said and looking at mine,
    i'm not sure if i just unhook #2 coil wire and leave the others #1 and #3 hooked together?
  20. This is how it should look before you start...

    This is how it should look before you start cutting and moving wires.
    227420
    any help on what to do from here thanks in advance.
  21. Replies
    104
    Views
    57,622

    i am working on the same one you have will be...

    i am working on the same one you have will be posting more info in the Forums under ...
  22. Seeing that it's a 208 volt could I not possibly...

    Seeing that it's a 208 volt could I not possibly create an external box to plug the welder into with a capacitors in the Box let's say hooking L1 to one of the 220 lines L2 to the other 220 line or...
  23. Sorry for the mess was tring to put all the info...

    Sorry for the mess was tring to put all the info on this cp-200 208/230 in one place after I had dug it up from searching the other posts. You have any advice on what to do on this, what else to try.
  24. Do you have a cleaner walk through on this? Or a...

    Do you have a cleaner walk through on this? Or a better way to do it?
  25. [QUOTE=Johnny5;2917379] Thanks for your help!...

    [QUOTE=Johnny5;2917379] Thanks for your help! damongooseman
    with your description i managed to convert my cp-200 (Canadian Version) with no fires, in a couple of hours!


    Quote Originally...
Results 1 to 25 of 51
Page 1 of 3 1 2 3