Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: TDegenhart

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. Well, that's the end of this site then. Tom

    Well, that's the end of this site then.

    Tom
  2. Replies
    8
    Views
    376

    That license may or may not do you any good. The...

    That license may or may not do you any good. The license he has may only apply to the physical copy he has.

    A lot of that type of software have codes embedded in the setup or install files that...
  3. Replies
    28
    Views
    1,401

    Maybe some grain growth but otherwise I see no...

    Maybe some grain growth but otherwise I see no harm.

    Tom
  4. Replies
    1,048
    Views
    282,260

    Google says ITAR is international traffic in arms...

    Google says ITAR is international traffic in arms regulations.

    Tom
  5. Replies
    1,048
    Views
    282,260

    Kinda early to start thinking out it, but what do...

    Kinda early to start thinking out it, but what do you plan on when it becomes time to be a professional snow bum. That's a lot of machinery and business.

    Tom
  6. I would sit down with the guy and explain the...

    I would sit down with the guy and explain the ridiculousness of the position he is in. Maybe in addition to the engineering and production education you gave him he needs some business teaching too....
  7. Replies
    10
    Views
    517

    You missed what I said. I cut the threads OFF...

    You missed what I said. I cut the threads OFF the bolts.

    Tom
  8. Replies
    10
    Views
    517

    You have just pointed out what little I know...

    You have just pointed out what little I know about inserts. The inserts in question are for turning and the holders and inserts are screw secured. But that is not the main question, I know so...
  9. Replies
    10
    Views
    517

    Carbide Insert Parts and Usage

    I don't do enough with inserts to warrant special attention from a sales person so I will ask the questions here. What are pads and shims and what are they used for?

    Tom
  10. Replies
    29
    Views
    1,391

    Get a knowledgeable contractor and a bank loan. ...

    Get a knowledgeable contractor and a bank loan.

    Tom
  11. Go split some chips. Make yourself useless. ...

    Go split some chips. Make yourself useless.

    Tom
  12. Replies
    133
    Views
    6,512

    I haven't read through all the posts so this may...

    I haven't read through all the posts so this may have already been suggested. Talk to Ox, he is one of the most reliable contributors here. He's located West Unity, Ohio.




    Tom
  13. How would barrel tumbling compare to vibratory...

    How would barrel tumbling compare to vibratory finishing?

    Tom
  14. Replies
    55
    Views
    2,375

    This is very good, I hope some of the non-EE's...

    This is very good, I hope some of the non-EE's study this.

    The current here is vary close of sinusoidal. Not so much when there is little or no air gap.

    Tom
  15. Replies
    56
    Views
    2,843

    Unless things have changed, R-22 is no long...

    Unless things have changed, R-22 is no long manufactured in the US nor can be imported. All the R-22 is either old stock or recycled. Same with R-12. Installation is not hard, just have to know...
  16. Replies
    55
    Views
    2,375

    I rather thought that was what you did. I have...

    I rather thought that was what you did. I have tried that with a scope using the zero crossing but because the current wave near zero is rather flat it was difficult to get a good value. Better to...
  17. Thread: Smoke

    by TDegenhart
    Replies
    48
    Views
    2,468

    My experience is go dry or flood. You could try...

    My experience is go dry or flood. You could try a fume extractor or fans and open doors and windows. Also a gas mask.

    Tom
  18. Replies
    55
    Views
    2,375

    You say it dissipates (draws) 200 watts. Is that...

    You say it dissipates (draws) 200 watts. Is that a guess, estimate or actual measurement with a watt meter?

    Tom
  19. Replies
    8
    Views
    458

    What are you planning on for the barrel? I made...

    What are you planning on for the barrel? I made one using a 5 gal paint bucket. It didn't last long, the walls were soon punctured. Use HF cement mixer or something like that.

    Tom
  20. Replies
    254
    Views
    31,347

    I am not completely familiar with the subject,...

    I am not completely familiar with the subject, but if it is an air compressor, then pulling from the outside would be the choice in winter as the air is cold and dry, just characteristics you want. ...
  21. There are recommendations for sizing caps, but...

    There are recommendations for sizing caps, but when it comes down to the wire its cut and try.

    Tom
  22. Replies
    41
    Views
    3,508

    You overlooked at least 3 forklifts. This must...

    You overlooked at least 3 forklifts.

    This must be just storage even thought there are electrical outlets all around. All of the other stuff from cannonmn have been about moving into an old house....
  23. Replies
    7
    Views
    639

    Brass too long? Tom

    Brass too long?

    Tom
  24. Replies
    33
    Views
    2,426

    I believe you have too high a spring constant, by...

    I believe you have too high a spring constant, by that I mean that a small deflection causes a large change in spring force. That also means that you have a small region that the spring will operate...
  25. Replies
    41
    Views
    3,508

    I think he is a collector, not a user. Tom

    I think he is a collector, not a user.

    Tom
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4