Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Will McRay

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    899

    Thank you. I have played with it and got the gap...

    Thank you. I have played with it and got the gap much closer now. Spoke with Steve at Monarch and he stated If the bearings were replaced, the dimensions may have change the flanged spacer may need...
  2. Does anyone have the instructions for using the...

    Does anyone have the instructions for using the taper attachment?


    Sent from my iPad using Tapatalk
  3. Replies
    13
    Views
    899

    Yes, the roller thrust bearing. IĒlol double...

    Yes, the roller thrust bearing. IĒlol double check the movement since my memory is not as strong as it used to be, but I think it does change.


    Sent from my iPhone using Tapatalk
  4. Replies
    13
    Views
    899

    Iíll check into that. I donít have the original...

    Iíll check into that. I donít have the original screw unfortunately and had not had the nerve to get a quote from Monarch. Might be another 500 dollar part. May make one.


    Sent from my iPhone...
  5. Replies
    13
    Views
    899

    It is a 10EE. I have taken it apart and replace...

    It is a 10EE. I have taken it apart and replace one roller thrust bearing on the other end. I tend to wonder if the acme thread or not is worn.
  6. Replies
    13
    Views
    899

    Compound backlash adjustment

    As you will see in the picture there is a gap between the dial and the compound. With a dial indicator and measuring the compound handle movement before actual compound movement is .040. How is...
  7. Replies
    4
    Views
    563

    Interesting guys. Thanks for the Monarch...

    Interesting guys. Thanks for the Monarch education.


    Sent from my iPhone using Tapatalk
  8. Replies
    4
    Views
    563

    What is it and whatís it for?

    I have seen in some 10EE pictures and in a few brochures and manuals on Vintage Machinery.org a rod that is stored on two hooks just below the apron, but canít find what it is or used for. My 10EE...
  9. Replies
    10
    Views
    709

    Thank you for that information. I really...

    Thank you for that information. I really appreciate it.


    Sent from my iPad using Tapatalk
  10. Replies
    10
    Views
    709

    Sure does, hence the reason to ask the question...

    Sure does, hence the reason to ask the question of an overall length. Need to know a starting point to procure material before machining. If I sound like an idiot so be it.


    Sent from my...
  11. Replies
    10
    Views
    709

    Would anyone know the overall length of the gib?...

    Would anyone know the overall length of the gib?


    Sent from my iPhone using Tapatalk
  12. Replies
    10
    Views
    709

    This is a great idea. Monarch wants $500 for a...

    This is a great idea. Monarch wants $500 for a new gib then it has to be cut to length and scraped in. Iím gonna look into this.


    Sent from my iPad using Tapatalk
  13. Replies
    10
    Views
    709

    Help! Cross Slide Gib EE-2054 Needed

    Hello everyone,

    My 10EE project is nearing its end and today as I was installing the cross slide i noticed the small end of the gib was broke. I don't know how much was broke off, but I can't...
  14. Replies
    6
    Views
    674

    That is good to know. Thank you. Sent from...

    That is good to know. Thank you.


    Sent from my iPhone using Tapatalk
  15. Replies
    6
    Views
    674

    Thanks for all this information. Believe it or...

    Thanks for all this information. Believe it or not, Monarch says there is a gasket for the bottom oil covers.

    Will


    Sent from my iPhone using Tapatalk
  16. Replies
    5
    Views
    782

    Interesting. From the looks of it, the button is...

    Interesting. From the looks of it, the button is missing.

    Thanks for the replies.

    Will


    Sent from my iPhone using Tapatalk
  17. Replies
    5
    Views
    782

    Help Identify What is and Used For

    It did not occur to me until today to figure what this is. Can anyone help identify what this and whatís it used...
  18. Replies
    6
    Views
    674

    10EE Apron Gaskets/Seals

    When I removed my apron I did not see a gasket between the carriage and apron. I have read there is a seal. Can anyone share some information on this?

    I also rebuild the oil pump in the apron and...
  19. Replies
    3
    Views
    912

    Greener No 4 arbor press

    This old gem followed me time today. Been looking for a while for an American made vintage ratcheting arbor press and just was not have good luck with driving distance until last week. Have a look. I...
  20. Replies
    8
    Views
    1,034

    10EE Carriage Bearings

    I disassembled and measured the bearings. searched the web and VXB turned out to be the best place to purchase from. These are 629ZZ bearings.

    Thanks Everyone for your help.

    Will


    Sent...
  21. Replies
    8
    Views
    1,034

    Thank you! Sent from my iPhone using Tapatalk

    Thank you!


    Sent from my iPhone using Tapatalk
  22. Replies
    8
    Views
    1,034

    Square dial. Yes, the four roller bearings. ...

    Square dial. Yes, the four roller bearings.

    Will


    Sent from my iPad using Tapatalk
  23. Replies
    8
    Views
    1,034

    I was looking for the carriage bearings, not the...

    I was looking for the carriage bearings, not the apron bearings but thanks because I am assess those too.

    Will


    Sent from my iPhone using Tapatalk
  24. Replies
    8
    Views
    1,034

    10EE Carriage Bearings

    Does anyone have any recommendations on where to find bearings for the carriage and what part number is the preferred?

    Will


    Sent from my iPhone using Tapatalk
  25. Replies
    13
    Views
    1,271

    I got the original order on the lathe and I did...

    I got the original order on the lathe and I did not see a light but I seem to have had a coolant pump so I assume that pump was fed by that transformer.

    Thank you for the additional education!...
Results 1 to 25 of 50
Page 1 of 2 1 2