Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: RRR

Search: Search took 0.00 seconds.

  1. Replies
    25
    Views
    1,829

    here are two schematic drawings of a single phase...

    here are two schematic drawings of a single phase dual voltage ,capacitor start motor with centrifugal switch . both drawing's are the same motor ( though id give you two versions of it )your motor...
  2. Replies
    25
    Views
    1,829

    found this how to trouble shoot a motor with...

    found this how to trouble shoot a motor with start cap and centrifugal switch that may be of help for you ? YouTube
  3. Thread: Drum switch wiring

    by RRR
    Replies
    3
    Views
    556

    269172269175 if the connection diagram...

    269172269175 if the connection diagram on the name plate mounted on the side of the motor looks the sketch of in the pic. then the motor to switch connection diagram (in next pic ) will...
  4. Replies
    25
    Views
    1,829

    a few motor schematic's that may be of use , the...

    a few motor schematic's that may be of use , the three original posted pic.s by the OP are a blur,( unable to read terminal designations and motor leads ) good luck269019269020269021
  5. Replies
    25
    Views
    1,829

    a single phase reversible continuous duty...

    a single phase reversible continuous duty capacitor start with centrifugal switch is a very ,very simple motor that can be wrung out with a meter and all wiring easily identified ,might suggest...
  6. Replies
    25
    Views
    1,829

    that's how it works on a single phase motor with...

    that's how it works on a single phase motor with forward/reverse and a 3 pole double throw switch . the wire needs to be size accordingly ,disconnect and breaker /overload ,provided for in power...
  7. Replies
    25
    Views
    1,829

    drew it up for you ,sir268496

    drew it up for you ,sir268496
  8. work in progress

    fast forward : been making chips for a while now ,try to post a few pic's of almost finished product (always a work in progress ) 223845223846
  9. Replies
    8
    Views
    1,059

    had big honking 16 down the road from me ,though...

    had big honking 16 down the road from me ,though about it ,was too busy with the 10L project ,bigger than what I need in my garage
  10. I let sit for about a year ,just jumped back on...

    I let sit for about a year ,just jumped back on it recently ,I acquired a new flame hardened bed and saddle with little to no where at all . went thru the gear box ,headstock and apron ( replaced...
  11. Thread: feed change lever

    by RRR
    Replies
    3
    Views
    1,531

    well that answers that ,.wasn't sure about the...

    well that answers that ,.wasn't sure about the lock out on the longitudinal (up )position , trying to get the 53 up and running ,thanks Mr Smith
  12. Thread: feed change lever

    by RRR
    Replies
    3
    Views
    1,531

    feed change lever

    purchased a used complete apron on # bay for parts for my wore out 53 10L ,decided to use the newly purchased apron as it shows very little if any wear at all on half nuts , gears, and bushings ect: ...
  13. i might just see if i can press that gear off...

    i might just see if i can press that gear off ,just to see how doable it is ,but ill probably just replace it .appreciate the advise fellows , fixing to check that back way with the tail and...
  14. already started on the head stock .found a broke...

    already started on the head stock .found a broke off gear tooth to the quill pinion gear . drug out the oxy/acetylene and silver soder .a little brazing and file work and the tooth is back . may...
  15. the belt ?

    the belt ?
  16. some pic's of the headstock tear down or rather...

    some pic's of the headstock tear down or rather removal. so hated to cut that belt (appears to be a leather /plastic hybrid ?) also had to beat hell out a that da gone tapered pin in the backgear...
  17. ,been real busy and not much time to mess with...

    ,been real busy and not much time to mess with it,had the opportunity to take a closer look at the wear on the ways for a better evaluation of the conditions of said ways . I'm thinking there not too...
  18. Replies
    9
    Views
    2,387

    very interesting and a lot of work . thanks for...

    very interesting and a lot of work . thanks for taking the time to do this ,ray
  19. looked at the shaft to the QC box that the...

    looked at the shaft to the QC box that the sifters are mounted on and you can push the shaft out right to left with fingers (whatever retains in place may be missing ., i'm more concerned with the...
  20. Had a chance to tinker with it a bit , took a...

    Had a chance to tinker with it a bit , took a part the top of the compound rest ( threads a bit bent ( wobbles when you roll it ) as well as the handle . Had to go slow as I am awaiting the delivery...
  21. i was thinking that too . i'll mostly be facing...

    i was thinking that too . i'll mostly be facing off barrels and threading em ,although would like too maybe do some more creative projects , may be able to work out past the wear with the center rest...
  22. new guy ,first post ,brought home a a heavy 10 (i think)?

    well ,been looking for a project ,looks like i found one , my first lathe ,looks like its all there ,double tumblers ,with a taper jig, a,few chucks and a center rest . found that theirs wear on the...
Results 1 to 22 of 22