Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: DavidScott

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds; generated 42 minute(s) ago.

  1. Replies
    26
    Views
    970

    Yes, abynormal. Thinking about this more,...

    Yes, abynormal.

    Thinking about this more, .005" in 1.5" is .04" a foot. That has to be more than the Z axis ways!
  2. Replies
    8
    Views
    274

    Poll: Kitamura and Enshu. While your at it you...

    Kitamura and Enshu.

    While your at it you should also ask 3, 4, or 5 axis. I would be currious about that.
  3. Replies
    26
    Views
    970

    What are you cutting?

    What are you cutting?
  4. The motor that moves the pot is an air motor so...

    The motor that moves the pot is an air motor so low air would make sense.

    There is an oiler for the air to the solenoid valves that takes turbine oil, your keeping oil in that correct? If it goes...
  5. Mine only uses about an inch out of the reservoir...

    Mine only uses about an inch out of the reservoir for every 300 hours of spindle time.

    Pull the tools out of the pot before pressing reset. It sounds like something is interupting the tool pot...
  6. Replies
    11
    Views
    525

    New aluminum specific carbide inserts, which are...

    New aluminum specific carbide inserts, which are rarely coated, but I have never used diamond so maybe that is the best.
  7. Replies
    508
    Views
    33,163

    Well, they do offer drivers too, god forbid. ...

    Well, they do offer drivers too, god forbid. Sometimes they will even replace your drivers with theirs, it has happened to me on my video card.
  8. Replies
    508
    Views
    33,163

    Ever update firmware and drivers on your...

    Ever update firmware and drivers on your computer? Rarely do you get notified that new versions are available.
  9. Replies
    508
    Views
    33,163

    This is a clear sign you are going senile. You...

    This is a clear sign you are going senile. You have good cnc machines but you are willing to go back to manual tool changes?:nutter:
  10. Replies
    15
    Views
    572

    What Peter said. I forget the formula but I...

    What Peter said. I forget the formula but I think you want about 3 diameters reamed then about .005" clearance for the rest of the hole. The tighter clearance helps hold the grease. Also, make...
  11. Replies
    508
    Views
    33,163

    I just have it turn my "high accuracy" mode on...

    I just have it turn my "high accuracy" mode on when I use cutter wear comp, ie G41, and turn it off with a G40. Rough without it and just turn it on when accuracy matters, like finish passes. Real...
  12. Replies
    20
    Views
    1,168

    80D is extremely hard for a plastic, I don't...

    80D is extremely hard for a plastic, I don't think I have ever machined any plastics that hard. Acetals and nylons are in the 65-70D range if memory serves, polyethylenes are softer. 70 to 80D is a...
  13. Replies
    20
    Views
    1,168

    Nevermind, I was thinking Shore A. No experience...

    Nevermind, I was thinking Shore A. No experience machining harder than 85A.
  14. Replies
    508
    Views
    33,163

    That is as bad as the old Fadal I ran.

    That is as bad as the old Fadal I ran.
  15. Replies
    120
    Views
    15,372

    If you know what you are doing it is just a bunch...

    If you know what you are doing it is just a bunch of simple things you have to do in the correct order, nothing is really hard. I built a frame with 2 2x4 and one 2x6 boards, stuff I had on hand, to...
  16. Replies
    120
    Views
    15,372

    I would pull the spindle out and send it in,...

    I would pull the spindle out and send it in, unless 1500$ isn't worth 2-3 days of your time, but you will know it is done right, which it doesn't sound like it was. I need to update my spindle...
  17. Replies
    508
    Views
    33,163

    I will back up the difference in cycle time. The...

    I will back up the difference in cycle time. The difference for me when measured is 1.5 seconds per minute between 50 and 100% with 2k rapids.
    The Brother turrets are servo driven so your only...
  18. Replies
    508
    Views
    33,163

    Have you ever run one? If not then don't. Those...

    Have you ever run one? If not then don't. Those fast chip to chip tool changes alone are addictive, let alone the fast, crips rapids of these little toys. I was ruined from the start. The two...
  19. Replies
    508
    Views
    33,163

    I thought they were coil springs? Not belvilles.

    I thought they were coil springs? Not belvilles.
  20. Replies
    508
    Views
    33,163

    I am parroting snippets of info I have heard on...

    I am parroting snippets of info I have heard on this forum, that is why I am not sure of the real numbers. Brother drawbar tension numbers are a closely guarded secret but I have been given quite a...
  21. Replies
    508
    Views
    33,163

    So some dual contact Brother spindles have the...

    So some dual contact Brother spindles have the same drawbar tension as standard spindles?
  22. Replies
    120
    Views
    15,372

    Sounds like you got the budget rebuild, they...

    Sounds like you got the budget rebuild, they didn't grind the taper. My tenths Interapid needle doesn't move on my spindle taper after its rebuild. Did they remove the motor in the process of...
  23. Replies
    508
    Views
    33,163

    With much more drawbar tension.

    With much more drawbar tension.
  24. Replies
    508
    Views
    33,163

    If that were happening would that not mark up the...

    If that were happening would that not mark up the taper some? That taper showed no fretting or other indication it had been pushed too hard, at least before it was.
  25. I would use a smooth, water-cooled, resin bond...

    I would use a smooth, water-cooled, resin bond diamond face wheel with the cutter in its holder so it could spin a little while I sharpen it. But that is just the best option in my shop, I don't know...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4