Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: wolfenstien

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thanks! I do have that on my phone and used...

    Thanks!

    I do have that on my phone and used it. Worked pretty well actually. The one thing that it doesn't do well is account for what machine your running it in.

    Example .750 niagra endmill...
  2. Fadal Speeds and feeds Generic templates

    Hoping Bobw and a few other fadal owners might chime in.
    I'm a home shop guy but have a VMC15 couple prototrak mills and a couple Mori lathes. I already have a day job and a part time job which...
  3. I always wondered what those rings were for. All...

    I always wondered what those rings were for. All the motor mounts have them I just couldn't understand why. makes sense now.

    Think I'd have any luck purchasing a replacement gear for the motor...
  4. Mori Seiki SL2B Z axis Servo Gearbox gear adapter

    Did a Centroid Retrofit on a Mori Sl1H I had last fall. Been happy with it so far. Don't use it much and am realizing now that I should have done the bigger Mori lathe I've got which has a dead...
  5. Replies
    42
    Views
    4,718

    If you ship it to me I'll store them for you :)

    If you ship it to me I'll store them for you :)
  6. Replies
    42
    Views
    4,718

    Just a couple thousand miles to far for me....

    Just a couple thousand miles to far for me. Otherwise I'd be there shortly with a trailer and a low ball offer in the form of a fist of cash.
  7. Are you in MDI? I can't punch or pull from my USB...

    Are you in MDI? I can't punch or pull from my USB in MDI. Hit manual again and try it in the other menu.

    TC,1 to receive from USB.
    PU,2,,0 to punch to USB.

    Make sure you have the commas in...
  8. Replies
    4
    Views
    530

    Note I know nothing about your machine, But I...

    Note I know nothing about your machine,

    But I would look for the way lube reservoir and fill it with whatever the manufacturer recommends for way lube.

    Again. I don't know anything about your...
  9. So it turns out I wasn't able to run without...

    So it turns out I wasn't able to run without modifying the soft limits. Because the program was 15.999 wide in Y I would have had to position the part within .0005 of CS position for the program to...
  10. Replies
    6
    Views
    777

    Turns out I had a box of these relays from parts...

    Turns out I had a box of these relays from parts machine I bought a bunch of boards out of.

    Replaced K11 and everything started working again. Ran the rest of the evening without any hiccups.
    ...
  11. Replies
    6
    Views
    777

    Ah, perfect, Thank you for the link too. I'll...

    Ah,

    perfect, Thank you for the link too. I'll get a couple ordered as well as some of the 3Amp so I've got some spares on hand.

    I let you know when if that makes a difference.
  12. Replies
    6
    Views
    777

    I should have snapped a photo of my board. Will...

    I should have snapped a photo of my board. Will try to remember to tonight when I'm at the machine. K11 and K12 are little soldiered on boards. May still be relays boards, but they are not removable...
  13. Replies
    6
    Views
    777

    Fadal VMC15 ATC only moves CCW

    I've owned this machine for nearly 3-4 years now I think. Hardly ever used it. Done few single tool longer programs with it. Did a couple small parts with a couple tools. But today was going to be my...
  14. Thanks Bob, I chickened out. Decided to go...

    Thanks Bob,

    I chickened out. Decided to go heavier on the roughing cut. (.045 radial DOC) and leave .005 per side put my program .001 from the soft limit. I'll run her there. No messing with the...
  15. Might be worth mentioning that this will be a 9mm...

    Might be worth mentioning that this will be a 9mm (smidge under 3/8 endmill) for profiling around the part only. Y will likely only be over the limit for a couple seconds. The X will need to travel...
  16. Ran to the limit shut the machine off and put an...

    Ran to the limit shut the machine off and put an indicator on the table and moved the ballscrew by hand in the x direction. I could get .150 but it was sort of squishy like pushing against rubber....
  17. Fadal VMC15 Soft limit to hard limit distance

    I'll probably go check this with the machine powered down when I get a chance but I've got a part that needs a little bit of extra clearance to profile all the way around and I was wondering if...
  18. Machine has now been moved to an online Auction. ...

    Machine has now been moved to an online Auction.

    High bidder takes it.

    3 axis Conversational CNC Knee Mill Anilam 33MK Box way Milling Machine (1999) | eBay
  19. This is now sold. Thanks!

    This is now sold. Thanks!
  20. Anybody got any suggestions on a reasonable...

    Anybody got any suggestions on a reasonable asking price on this machine?
  21. Hardinge DV-59 Headstock (With Collet closer assembly)

    Bought this some time back. Meant to build a live tooled tailstock for my lathe, but never got around to it. Other projects need the funds and I've lost interest for now. Let me know if one of you...
  22. 3 Axis CNC Knee Mill Anilam 3300MK Control, Box way, 30 Taper, Power Drawbar

    Just posted this one.

    P.M. me an offer if your interested.

    Can help out with delivery if you within 100 miles.

    3 axis Conversational CNC Knee Mill Anilam 33MK Box way Milling Machine...
  23. Replies
    2
    Views
    719

    Is Maine close enough? :)

    Is Maine close enough?

    :)
  24. BUMP with Price Drop. NOW $1200! The AMC...

    BUMP with Price Drop.

    NOW $1200!

    The AMC (ADVANCED MOTION CONTROLS)...
  25. Bump Sweo Drive is sold. AMC drive still...

    Bump

    Sweo Drive is sold.

    AMC drive still available. $100 off for PM members.
Results 1 to 25 of 112
Page 1 of 5 1 2 3 4