Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: pigpen60

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    1,425

    Never assume that just because its a zerk that it...

    Never assume that just because its a zerk that it needs grease!
  2. Thread: What is it?

    by pigpen60
    Replies
    19
    Views
    1,564

    Thanks E189552 for the reply, I didnt realize...

    Thanks E189552 for the reply, I didnt realize that this site had become so elitist. I didnt know it was forbidden to ask questions, sorry.
  3. Thread: What is it?

    by pigpen60
    Replies
    19
    Views
    1,564

    What is it?

    Anybody have any idea what this is? It came from McDonnell Douglas.258616258617
  4. Thread: What is this?

    by pigpen60
    Replies
    8
    Views
    1,025

    Thank you for the quick response!

    Thank you for the quick response!
  5. Thread: What is this?

    by pigpen60
    Replies
    8
    Views
    1,025

    What is this?

    Any idea what this is?
    220330
  6. Replies
    3
    Views
    1,274

    Ouch! Thank you.

    Ouch! Thank you.
  7. Replies
    3
    Views
    1,274

    CNC plasma/waterjet under $10k

    Is it possible to get a reliable CNC plasma or waterjet cutting system for under $10K?
  8. Replies
    28
    Views
    19,971

    and here...

    and here http://armymunitions.tpub.com/mm0145a/Figure-2-31-105Mm-Semi-Fixed-He-And-Extended-Range-Cartridges-62.htm now note that it says M28B2 not M2882 for the primer but if you look close like at...
  9. Replies
    28
    Views
    19,971

    Go here Johnston Atoll Chemical Agent Disposal...

    Go here Johnston Atoll Chemical Agent Disposal System (JACADS): Environmental Impact ... - Google Books
  10. Replies
    22
    Views
    3,629

    Looks like your going to have to syphon the water.

    Looks like your going to have to syphon the water.
  11. the roadside is no place for these memorials in...

    the roadside is no place for these memorials in my opinion. you pay to bury the remains and put a headstone in place. and then folks go and grieve at the place of the death not at the place of...
  12. Replies
    58
    Views
    6,979

    didnt they use a toyota to tow the space shuttle?...

    didnt they use a toyota to tow the space shuttle? good enough for me!
  13. Thread: material help

    by pigpen60
    Replies
    9
    Views
    2,078

    material help

    my wife has a craftsman nextec 12 volt trimmer and it uses a flail instead of trimmer line. my problem is they quit making the flails, any idea what type of material would work to make my own? forgot...
  14. Replies
    11
    Views
    1,633

    figured someone would have done this already and...

    figured someone would have done this already and i was just hoping for your thoughts on the setup. a fella where i work milled a flat on said rod by moving it in the vise repeatedly. not precision...
  15. Replies
    11
    Views
    1,633

    36" long. tom

    36" long. tom
  16. Replies
    11
    Views
    1,633

    how to setup rod for milling

    how would you secure a .250" rod for milling a flat on its entire length? tom
  17. Replies
    28
    Views
    3,417

    but maybe if someone called that spoke the...

    but maybe if someone called that spoke the language ?
  18. Replies
    1,380
    Views
    721,039

    so when you did that keyway on that large...

    so when you did that keyway on that large rotor/armature the pipe was just to get the shaft out to the crane the fork truck was for safety and you raised the table up and if needed the crane as you...
  19. Replies
    1,380
    Views
    721,039

    late to the party

    a question about using the jib crane to hold the end of long work in the mill. wouldnt the one end of the work raise or lower when you moved the table? tom
  20. Replies
    8
    Views
    3,067

    if it has a drawbar (threaded rod) that tightens...

    if it has a drawbar (threaded rod) that tightens the collet just thread it back in and give it a whack on the head. hope this helps, tom
  21. Replies
    8
    Views
    15,561

    i apreciate yall's patience with my questions....

    i apreciate yall's patience with my questions. probably should have asked for a book recommendation that would have tool use in it if one exist. tom
  22. Replies
    10
    Views
    6,860

    moore tool book

    someone mentioned a book by moore tool that showed various ways to use 123 blocks in setups. any idea what the name of the book is and where you might find it? thank you, tom
  23. Replies
    8
    Views
    15,561

    i was thinking it was for grinding, looks too...

    i was thinking it was for grinding, looks too fragile? for miling. what i mean is with the straps for locking it in position it doesnt look like it would take much abuse. make sense? tom
  24. Replies
    8
    Views
    15,561

    sine plate use

    my question is what do you use a sine plate for, i understand how it works just not when to use it. a pic of it in use would help. tom
  25. Replies
    2
    Views
    1,070

    inspection plate

    i have a 12"X18" cast iron inspection plate(or so yall told me:D) what/when do you do with a inspection plate? tom
Results 1 to 25 of 35
Page 1 of 2 1 2