Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: primeholy

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    1,616

    I believe I found the battery. Our electrician...

    I believe I found the battery. Our electrician thinks he might have a replacement! Hopefully this works!
  2. Replies
    5
    Views
    1,616

    I am having this same alarm this morning on my...

    I am having this same alarm this morning on my quickturn. Where are the batteries located? The turret is also louder on about half of the tool change positions.
  3. My sweet spot at ramping is 2 degrees. However, I...

    My sweet spot at ramping is 2 degrees. However, I dont cut a lot of aluminum nowadays. I cut mainly 1018,4140 pre, h13, d2, and some others. Oh, and stellite. I hate stellite.
  4. Replies
    47
    Views
    3,962

    I use volumill for all roughing except for when...

    I use volumill for all roughing except for when I'm doing mold cavities. I use 900 sfm with 4140,1050 on 1018. Stepover varies with DOC. We are using some kind of niagara 1/2 5 flute em.
  5. Replies
    6
    Views
    629

    Yeah, its made by finkl. Die Steel - Finkl Steel...

    Yeah, its made by finkl.
    Die Steel - Finkl Steel
    https://www.finkl.com/wp-content/uploads/2018/05/FX_EN_feb18.pdf
  6. Replies
    6
    Views
    629

    Heat shrink holders and balancers

    How many of you that use heat shrink holders also balance your tools? We run our finishing tools (6mm,4mm,2mm,1mm ball nose) at 20,000 rpm. We are having issues with surface finish on our Makino F5,...
  7. Replies
    345
    Views
    48,146

    So, this guy took his ball and went home. Is the...

    So, this guy took his ball and went home. Is the project still active?
  8. Replies
    14
    Views
    1,551

    We have a romer arm. I wonder how accurate this...

    We have a romer arm. I wonder how accurate this is in comparison.
  9. Replies
    29
    Views
    3,161

    I think he will need at least 3 holes. If he can...

    I think he will need at least 3 holes. If he can get away with that, that is a good way to go.
  10. Replies
    29
    Views
    3,161

    YouTube...

    YouTube
    Here's another
  11. Replies
    29
    Views
    3,161

    Also, if it is a job you are going to be tearing...

    Also, if it is a job you are going to be tearing down and setting up, you could put two 1/4 inch dowel holes in your jaws when you make them initially, and install them with the (long)dowels going in...
  12. Replies
    29
    Views
    3,161

    YouTube...

    YouTube
    Here is an example I found quickly to give you reference. Your part is going to be a little more tricky to hole, but I think you can figure something out.
  13. Replies
    29
    Views
    3,161

    With the soft jaws, you cut the outside profile...

    With the soft jaws, you cut the outside profile of the part into the jaws so you can hold them firm, and repeat. You may have to go with bigger soft jaws,depending on how you want to hold the part.If...
  14. Replies
    29
    Views
    3,161

    With there being no holes in the part, I would...

    With there being no holes in the part, I would lean towards thicker bar stock, use two vises, one to face and profile, next with machined soft jaws to deck to thickness, and chamfer if needed. Looks...
  15. Replies
    14
    Views
    1,153

    I would call it "added chatter".

    I would call it "added chatter".
  16. Replies
    15
    Views
    3,665

    Thanks, following

    Thanks, following
  17. Replies
    19
    Views
    2,891

    I've used this for about 6-7 years now. ...

    I've used this for about 6-7 years now.

    Machinist Calculator SFM on the App Store
  18. Replies
    0
    Views
    1,883

    Program Restart

    At what point do you enter 2 in sequence no. in the program restart screen? Is it after 2 million lines? One of my operators asked me today, and I dont remember. We enter line # in the Times column...
  19. Replies
    4
    Views
    1,273

    I work in a large forge plant. When production is...

    I work in a large forge plant. When production is down, we don't need the capacity to run the full plant, just the 3 machines. The compressors we use to run the entire plant are enormous.(i should...
  20. Replies
    24
    Views
    2,118

    Air Compressor reccomendations

    Good morning. I am wondering what kind of compressor I would need for two Makino F5s and an F8. Some Fridays production is down, so maintenance is doing their thing, and we don't get to use the main...
  21. Replies
    4
    Views
    1,273

    Air compressor reccomendations

    Good morning. I am wondering what kind of compressor I would need for two F5s and an F8. Some Fridays production is down, so maintenance is doing their thing, and we don't get to use the main...
  22. Replies
    18
    Views
    1,826

    Calculating surface feet ball nose tooling

    Hello. I am a programmer at a forge plant. Our dies are made out of Finkel grade 2(fx2) material. We have been using the same F.R. and rpms for 6-7 years now. My boss is wanting me to optimize our...
  23. It says "120 soft limit Z" Thanks

    It says "120 soft limit Z"
    Thanks
  24. TPC issue at tool change Mazak Quick turn 640T

    Every time we use the tailstock and use TPC, we are getting an over travel alarm at tool change. We have to reset, and index to the next used tool, then do a program restart at that unit.
  25. Replies
    19
    Views
    4,086

    I am having an issue related to TPC. Every time I...

    I am having an issue related to TPC. Every time I use TPC, I get an over travel alarm when the machine goes to do a tool change.
Results 1 to 25 of 28
Page 1 of 2 1 2