Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Will McRay

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    270

    I could accept a small seep, but I have a...

    I could accept a small seep, but I have a gusher...
  2. Replies
    3
    Views
    270

    K&T 2HL PTO Coolant Drive Leak

    Anyone with a 2HL, can you tell me if the shaft the drives the Coolant pump leak knee oil when spinning in the block mid point next to the rapid clutch? The rapids shaft does not leak. If leakage...
  3. Replies
    14
    Views
    866

    I was thinking the same thing with the clear coat.

    I was thinking the same thing with the clear coat.
  4. Replies
    14
    Views
    866

    287585 287586 287589 287588

    287585

    287586

    287589

    287588
  5. Replies
    14
    Views
    866

    287580 287581 287582 287583 287584

    287580

    287581

    287582

    287583

    287584
  6. Replies
    14
    Views
    866

    287575 287576 287577 287578 287579

    287575

    287576

    287577

    287578

    287579
  7. Replies
    14
    Views
    866

    287570 287571 287572 287573 287574

    287570

    287571

    287572

    287573

    287574
  8. Replies
    14
    Views
    866

    New to me: 1940 Monarch 18-BB or CBB

    I came across a Monarch 18-CBB manufactured in 1940 about 5 hours away from and could not pass on the deal. This was purchase by the New York Ship Building Corporation in Camden, NJ in Jan 16, 1940....
  9. Replies
    2
    Views
    701

    1940 Monarch 18-BB or CBB

    I have a 1940 Monarch 18-BB or CBB coming home soon. It's in great shape for its age. Currently wired for 440V and don't believe it dual voltage, but will pull the cover and check the wires. Looking...
  10. Does anyone have a copy of the manual for the...

    Does anyone have a copy of the manual for the 16-3 with my features and possibly the electrical schematic that I can get?
  11. Good to know. I was not aware of this. Thank...

    Good to know. I was not aware of this. Thank you.
  12. Thanks Steve. I am going to wire for 240. May...

    Thanks Steve. I am going to wire for 240. May have to reach out to you wiring configuration if I can find a diagram.
  13. This is great guys! Thank you so much. I am...

    This is great guys! Thank you so much. I am finalizing the deal now. The seller did open the motor cover and there are 12 wires so this is dual voltage as you stated. More to learn about this...
  14. DoAll 16-3 Vertical Bandsaw with Hydraulic Table Motor Voltage Question

    I have come across a DoAll 16-3 bandsaw with the hydraulic table. The data plate says it's 440V. I am looking for information on whether the motor is dual voltage or not. The seller sent me pictures...
  15. Replies
    13
    Views
    1,323

    Thank you. I have played with it and got the gap...

    Thank you. I have played with it and got the gap much closer now. Spoke with Steve at Monarch and he stated If the bearings were replaced, the dimensions may have change the flanged spacer may need...
  16. Does anyone have the instructions for using the...

    Does anyone have the instructions for using the taper attachment?


    Sent from my iPad using Tapatalk
  17. Replies
    13
    Views
    1,323

    Yes, the roller thrust bearing. IĒlol double...

    Yes, the roller thrust bearing. IĒlol double check the movement since my memory is not as strong as it used to be, but I think it does change.


    Sent from my iPhone using Tapatalk
  18. Replies
    13
    Views
    1,323

    Iíll check into that. I donít have the original...

    Iíll check into that. I donít have the original screw unfortunately and had not had the nerve to get a quote from Monarch. Might be another 500 dollar part. May make one.


    Sent from my iPhone...
  19. Replies
    13
    Views
    1,323

    It is a 10EE. I have taken it apart and replace...

    It is a 10EE. I have taken it apart and replace one roller thrust bearing on the other end. I tend to wonder if the acme thread or not is worn.
  20. Replies
    13
    Views
    1,323

    Compound backlash adjustment

    As you will see in the picture there is a gap between the dial and the compound. With a dial indicator and measuring the compound handle movement before actual compound movement is .040. How is...
  21. Replies
    4
    Views
    728

    Interesting guys. Thanks for the Monarch...

    Interesting guys. Thanks for the Monarch education.


    Sent from my iPhone using Tapatalk
  22. Replies
    4
    Views
    728

    What is it and whatís it for?

    I have seen in some 10EE pictures and in a few brochures and manuals on Vintage Machinery.org a rod that is stored on two hooks just below the apron, but canít find what it is or used for. My 10EE...
  23. Replies
    10
    Views
    1,071

    Thank you for that information. I really...

    Thank you for that information. I really appreciate it.


    Sent from my iPad using Tapatalk
  24. Replies
    10
    Views
    1,071

    Sure does, hence the reason to ask the question...

    Sure does, hence the reason to ask the question of an overall length. Need to know a starting point to procure material before machining. If I sound like an idiot so be it.


    Sent from my...
  25. Replies
    10
    Views
    1,071

    Would anyone know the overall length of the gib?...

    Would anyone know the overall length of the gib?


    Sent from my iPhone using Tapatalk
Results 1 to 25 of 64
Page 1 of 3 1 2 3