Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: discodan

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. When I bought mine it was covered in black paint...

    When I bought mine it was covered in black paint as part of a telescope mount and I could not see a makers mark. I kept looking at dividing heads on eBay until I found one that looked like mine and...
  2. Replies
    1
    Views
    551

    I have a new in box Lyndex. Here is a link to...

    I have a new in box Lyndex. Here is a link to what I have. If interested please I'M me. R8 1.1/4 Shell Mill Holder
  3. If tommy1010 is out of taps I have four 1-1/2"...

    If tommy1010 is out of taps I have four 1-1/2" 8tpi taps in used condition.
    Reif & Nestor 4 flute bottoming tap
    Vermont 4 flute bottoming tap
    Greenfield 6 flute bottoming tap
    Unknown brand 6...
  4. Replies
    29
    Views
    2,414

    I just bought the 1966 version of How to Run a...

    I just bought the 1966 version of How to Run a Lathe if interested.
  5. Replies
    14
    Views
    1,025

    I have 3/4", 1/2" and 3/8" and can easily cut you...

    I have 3/4", 1/2" and 3/8" and can easily cut you an 8" or longer piece. I also have some gears that will work with the 1/2". Note that everything has surface rust on it, so hopefully you don't need...
  6. Replies
    14
    Views
    1,025

    I have some in various sizes and lengths at home...

    I have some in various sizes and lengths at home I am happy to pass along. I won't be home until Tuesday and I will check what I have and post it here.
  7. By any chance in the collection of collets you...

    By any chance in the collection of collets you bought did you get any duplicates? I only have one true 4pn collet, a 3/16. I have a 3/4" but it looks like it may be shop-made because it has no...
  8. You must be the one who bought the recent one on...

    You must be the one who bought the recent one on eBay. I also have the P&W 3C horizontal mill. I recently bought a dividing head but I only got one collet and two dividing plates. I am keeping my...
  9. FS: FMC Syntron PowerPulse Controller and V-4-RC Magnetic Vibrator

    FMC Syntron PowerPulse Controller part #225484-A and a FMC magnetic vibrator part #V-4-RC. Neither part shows any wear whatsoever and I assume they are both new. On the auction site the controller...
  10. Picked up Keller power hacksaw this weekend

    Picked up the 3b (I think) at an estate sale. Needs a little attention but for $20 who can complain!
  11. Richard, in another forum I mentioned that I met...

    Richard, in another forum I mentioned that I met Paulo at Tuckahoe this past weekend as he was demonstrating his scraping skills you taught him. I intend on starting to volunteer in their shop and...
  12. Assuming you have vented soffits, the current...

    Assuming you have vented soffits, the current wisdom is to use passive ventilation from the soffit up through a ridge vent. That is what I did and I have a typical gable roof with soffit in front and...
  13. That's a nice looking machine! Wish I had a head...

    That's a nice looking machine! Wish I had a head like that for my P&W 3C.
  14. Replies
    12
    Views
    1,476

    JST, I am curious about the vertical head...

    JST, I am curious about the vertical head attachment. Is that custom or from some other machine? It would work nicely on my P&W 3C. Thanks
  15. Replies
    6
    Views
    845

    I am curious what head you have. I have a similar...

    I am curious what head you have. I have a similar P&W 3C mill.
  16. If you can give dimensions of the collet I can...

    If you can give dimensions of the collet I can help you narrow it down.
  17. Let me know what he says. If you don't want it I...

    Let me know what he says. If you don't want it I might be interested.
  18. Maybe try this. If you can, on your draw bar,...

    Maybe try this. If you can, on your draw bar, measure the TPI and the diameter and reference against this source. That may narrow it down to a few collets and then you can figure it out from there.
    ...
  19. Replies
    51
    Views
    6,674

    He was online yesterday. This is how you turn...

    He was online yesterday. This is how you turn into a bad seller.
  20. Jeff, I live on the western shore, in Arnold. I...

    Jeff, I live on the western shore, in Arnold. I have two books on Hartness lathes, one is a manual for a flat turret lathe and the other is for a double-spindle flat turret lathe. Is there any...
  21. Replies
    6
    Views
    1,442

    SOLD the vise!

    SOLD the vise!
  22. I'm trying to afford to replace some parts of my...

    I'm trying to afford to replace some parts of my OT make of lathe so that I can start threading and also buy a dividing head for my P&W 3C mill so I can start cutting some gears. If my FS posts are...
  23. FS: Lyndex shell mill holder - new in box.

    Shell Mill Holder, Taper Size R8, Pilot Diameter 1.25 In., Pilot Length 0.69 In., Projection 1.00 In., Body Dia. 2.88 In., Lock Screw Thread Size 5/8-18, For Use With Shell Mill.

    New from Lyndex...
  24. FS: CDI Chicago knife edge base depth micrometer .125" range

    CDI Chicago knife edge base depth micrometer. Measures depths of slots, grooves, recesses, etc. With knife edge base, and needle point contact, depths of up to .125" can be accurately measured. The...
  25. Replies
    6
    Views
    1,442

    $475? I want to sell so I can pick up some other...

    $475? I want to sell so I can pick up some other pieces from an estate sale.
Results 1 to 25 of 69
Page 1 of 3 1 2 3