Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: WillWilly

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    271

    Monarch EE Lathe, s/n 47245, 12-1/2 Swing x 20"...

    Monarch EE Lathe, s/n 47245, 12-1/2 Swing x 20" BC, 8" 3-Jaw Chuck, Tool Post, Tailstock Acu-Rite Pro DRO - Price Estimate: US$ - US$

    Monarch 10EE Same auction
  2. Replies
    4
    Views
    271

    I you look at this sale, there are several...

    I you look at this sale, there are several lathes, Monarch 10EE, CK... If you are near NE PA, could be a deal?
  3. Replies
    105
    Views
    12,228

    271806 Zero! 271807 Calling that good.

    271806

    Zero!

    271807

    Calling that good.
  4. Well, damn... I'm about to do the same job, same...

    Well, damn... I'm about to do the same job, same lathe. Im knee deep into my rebuild, and if these were mine, i would replace. Depends on what you plan on doing with your lathe and budget.

    What...
  5. Replies
    4
    Views
    271

    Cheap Monarch K?

    Monarch 14" x 54" Lathe, s/n 25135, 8" 3-Jaw Chuck, Tool Post, Steady Rest, Tailstock, 18-750 RPM - Price Estimate: US$ - US$
  6. Replies
    105
    Views
    12,228

    Thank you very much.

    Thank you very much.
  7. Replies
    105
    Views
    12,228

    That would be perfect. Thank you. Yes. Im...

    That would be perfect. Thank you. Yes.

    Im repairing the rod, attaching what is left of the mount.
  8. Replies
    105
    Views
    12,228

    271578 271579 I have finished the TA...

    271578

    271579

    I have finished the TA rebuild, checking the results with setting zero on my new magnifying lens and quantifying wear. I find once I set to zero, I have 0.0006" of wear in the...
  9. Replies
    105
    Views
    12,228

    Well I wasn't far off. That's almost exactly...

    Well I wasn't far off. That's almost exactly what I did. I have no knocking transitioning from 8 to 6 bearings on either side, horizontal or vertical. I have a very slight rubbing on the cover...
  10. Replies
    105
    Views
    12,228

    271335 271336 271337 271338 I figured...

    271335

    271336

    271337

    271338

    I figured out how to add photos from my phone. Use the full site rather than app.
  11. Replies
    105
    Views
    12,228

    I have my TA base assembled, new bearings,...

    I have my TA base assembled, new bearings, wipers, ready to do bench adjustment on the vetical bearings, larger bearings that keep the glide level.

    I could use advise on this step. Theory,...
  12. Replies
    105
    Views
    12,228

    I did the same with my "reference" pin. I'm...

    I did the same with my "reference" pin.

    I'm not opposed to China manufactured products, but wanted to attempt to stay true to the Timkenized theme. It isn't possable with these smaller bearings....
  13. Replies
    3
    Views
    319

    This is next for my CY. Excellent Post. Thanks...

    This is next for my CY. Excellent Post. Thanks so much.
  14. Replies
    105
    Views
    12,228

    So a couple questions: On the 8 horizontal...

    So a couple questions:

    On the 8 horizontal bearings for the TA, was one of yours non adjustable? On mine, the second from the right on the operator side bearing pin is not eccentric and didn't...
  15. Replies
    105
    Views
    12,228

    Taper Attachment Clamp Rod Broke

    On my lathe, the TA clamp and rod were missing and the rod mount is broke.

    So I'm looking for a replacement but this is very unlikely. I have seen only one Monarch TA clamp on Ebay that "might...
  16. Replies
    105
    Views
    12,228

    TA Adjustment gear

    I mentioned earlier finding that there were several broken bearings in the Taper attachment, all four were broken in the slide (See Picture). I have also found the adjustment gear for the Taper...
  17. Replies
    105
    Views
    12,228

    I'm getting into the details of the Taper...

    I'm getting into the details of the Taper Attachment. One is replacing the magnifying lens for the attachment adjustment.

    As I can see, there were originally two lenses, one to magnify and the...
  18. Replies
    105
    Views
    12,228

    I have mine all cleaned and going through as you....

    I have mine all cleaned and going through as you. I'll try to add some pictures. Mine is identical you yours.

    Unfortunately the rod on my was broke at some point and missing. I'll have to come...
  19. Replies
    13
    Views
    1,175

    Thanks Naro. I took it to work and finished....

    Thanks Naro. I took it to work and finished. Turned out well.
  20. Replies
    13
    Views
    1,175

    Took it to work and did it myself. Not the best...

    Took it to work and did it myself. Not the best option but had a great time doing it... I will post on "My winter project"
  21. Replies
    14
    Views
    1,126

    I'm looking for this part. It is on the back...

    I'm looking for this part. It is on the back side of the tool post cross slide. They are spring loaded hold downs for the cover over the saddle. I don't know if the 612 has these parts but I...
  22. I too have a CY16 1943 and I also had a reversing...

    I too have a CY16 1943 and I also had a reversing starter. After rebuilding the headbox with all new bearings (see forum post, My Winter Project) I decided to remove the reversing starter. The...
  23. Replies
    105
    Views
    12,228

    Very nice! My post does not have the oiling...

    Very nice! My post does not have the oiling port! It sure needs one though. I like the oil groove as well. I'm going to look at duplicating this port. I believe I will make the oil groove...
  24. Replies
    105
    Views
    12,228

    Yes Please... I pulled my slide for the parts...

    Yes Please... I pulled my slide for the parts washer and worked on the center hole as you suggested. On mine, this is the center for turning the post. This isn't a hole on mine. I agree that...
  25. Replies
    105
    Views
    12,228

    You are very correct. I took it apart and this...

    You are very correct. I took it apart and this is a "dutch pin" holding the post in place. Should have known. Monarch wouldn't have used cast surface as the pivot material. I'm not going to remove...
Results 1 to 25 of 124
Page 1 of 5 1 2 3 4