Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: yardbird

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    16
    Views
    1,036

    "Give that a try"? I was just posting a...

    "Give that a try"?

    I was just posting a example to look at but if you are literally going to try to reproduce what I did here is the rest of the program. G76 programs just skims the .875" OD, I...
  2. Replies
    16
    Views
    1,036

    I did this just messing around back in 2014. Code...

    I did this just messing around back in 2014. Code wise this is what I did. Something to look at anyway?

    N50(RIGHT HAND)
    G0G40G54X14.Z3.T0
    T0707
    G97S300M3
    G0X7.Z.2
    G0X.925Z.1M8
    ...
  3. Replies
    16
    Views
    1,036

    Another thing, if you have a machine with a Fanuc...

    Another thing, if you have a machine with a Fanuc control that uses the two line G76 cycle I'd switch it over to FS15 and use the one line format for the ease of programming, especially if you're...
  4. Replies
    16
    Views
    1,036

    What control do you have? I jacked around with...

    What control do you have? I jacked around with this once. Ended up with a diamond shaped pattern, if refined could it could resemble a knurled surface. I can post the code later tonight when I get in...
  5. Replies
    11
    Views
    515

    Well Bob I'd give slowing it down a go? For...

    Well Bob I'd give slowing it down a go?

    For ACME that's fairly quick. :ack2:

    Brent
  6. Replies
    30
    Views
    1,651

    You never came back, how did your 1/2"-14 NPT...

    You never came back, how did your 1/2"-14 NPT parts turn out? Are you using an aircraft style drill? That's a long 1/4" hole.

    I've seen them high pressure coolant through carbide drills do some...
  7. Congratulations! Hope everyone is doing well. The...

    Congratulations! Hope everyone is doing well. The guy in 26 joined up just to post about homing the turret. Sounds like that could probably be it? I run one of these 30 years ago but I don't remember...
  8. Replies
    7
    Views
    652

    I was going to say the reason why it fell off is...

    I was going to say the reason why it fell off is it looks like the first three threads out on the end are missing or buggered up.

    Brent
  9. We've been using this stuff for a few years now....

    We've been using this stuff for a few years now. It set for three months during COVID shut down and wasn't nasty when I came back. Actually I've never changed it only added to it.

    Brent

    321403
  10. Thread: Fanuc 21i-T

    by yardbird
    Replies
    13
    Views
    945

    What in the world made you ask this question in...

    What in the world made you ask this question in this thread? I believe if you type in O5150 not zero but the capital letter O and a 4 digit program number plus the "EOB" (end of block) then "insert"...
  11. Thread: O.T.CBD oil

    by yardbird
    Replies
    71
    Views
    9,894

    Teach, not gonna have to worry about that...

    Teach, not gonna have to worry about that anymore. CV got the boot! Actually I think that is his last post?

    Brent
  12. Replies
    15
    Views
    1,032

    My day shit counterpart makes a bunch of these. I...

    My day shit counterpart makes a bunch of these. I myself don't make them. They are for inhouse use. Butter them up with pipe dope and wrencher down. He is cutting the taper before chasing the...
  13. Replies
    15
    Views
    1,032

    You do like all the straight threads but you add...

    You do like all the straight threads but you add a R to the second line. It's the distance in radius value of the total Z move. If nobody shows up with one and if I remember can post an example when...
  14. I always only use one set screw. Typically it's...

    I always only use one set screw. Typically it's the one on the end or furthest from the insert.

    Brent
  15. Replies
    11
    Views
    671

    What do you need the door open for? Write a...

    What do you need the door open for? Write a program, watch it run out in dry land then let'er rip.

    Brent
  16. Replies
    18
    Views
    1,282

    I don't see any reason not to give it a go. Good...

    I don't see any reason not to give it a go. Good luck!

    Brent
  17. Replies
    18
    Views
    1,282

    Don't get pissed off but I can't tell if this is...

    Don't get pissed off but I can't tell if this is a serious question or you're just fucking with us? I think the hand wheel is how it's done on a Bridgeport for like a hundred years. The jog would be...
  18. Thread: Fanuc 21i-T

    by yardbird
    Replies
    13
    Views
    945

    I'm finding it hard to swallow that a Fanuc i...

    I'm finding it hard to swallow that a Fanuc i series controlled machine doesn't have G54-G59 fixture offsets.

    Brent
  19. Wonder what is the "there's more to this"? Just...

    Wonder what is the "there's more to this"? Just how well do you know this guy? It sounds like a few old stoners I know. You sure he ain't a burnt out pothead?

    Brent
  20. G74 is face grooving or peck drilling. I don't...

    G74 is face grooving or peck drilling. I don't believe you need both G74 lines for just drilling. You might look at G83. G83 is deep hole drilling with full retract.

    G0 X.0 Z.1
    G83 Z-2.54966...
  21. I'm running a part that gets tapped 1/2-13 now....

    I'm running a part that gets tapped 1/2-13 now. Fanuc 0i-T control

    G0 X0 Z.5
    G32 Z-1.35 F.076923
    Z.5 M4

    Is the exact code I'm using. Only reason I use G32 to tap is because G32 disables the...
  22. Is the T.2 a typo? No X pull out. G0 X0 Z.2...

    Is the T.2 a typo?

    No X pull out.

    G0 X0 Z.2
    G32 Z-2. F.0625
    Z.2 M3

    Brent
  23. Replies
    27
    Views
    1,568

    My guess is he don't know the difference. I was...

    My guess is he don't know the difference. I was under the impression G78 and G76 in function were damn near identical. Only difference was the call numbers. The G78 program he used doesn't look like...
  24. Replies
    14
    Views
    803

    I don't know jack shit about Mazak and I haven't...

    I don't know jack shit about Mazak and I haven't watched this video and it's for the T2 T3 control but there may be some good information in there that could possibly help?

    Brent
    ...
  25. Replies
    54
    Views
    3,146

    As you've probably noticed we ain't got a ability...

    As you've probably noticed we ain't got a ability to turn it off. Lol

    For the record I believed you from the beginning. The program looks different from the way I do thing but that doesn't...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4