Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: plumberpieco

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    14
    Views
    1,690

    I like the skid method with pallet jack. As said...

    I like the skid method with pallet jack. As said before the skid needs to be stout.264311
  2. That is the only photo I have. It is very clear...

    That is the only photo I have. It is very clear on my phone, Iíll try to send it to you direct. When I tried to find it myself I didnít have much luck.
    Z
  3. I recently went through the process of replacing...

    I recently went through the process of replacing the switch on my Condor.
    After getting several different switches I settled on a rotery switch advertised for a tire changing machine. Reason being...
  4. Replies
    29
    Views
    2,375

    258943 258944 Hereís a few cartoons

    258943
    258944

    Hereís a few cartoons
  5. Replies
    29
    Views
    2,375

    I recently picked up a 1945 10ee that hadnít been...

    I recently picked up a 1945 10ee that hadnít been run in probably 25+ years. Looked terrible, I read just about every post on the MG several times before I got started. Same problem withe the main...
  6. Have a Gorton 0-18a with #30 taper, great small...

    Have a Gorton 0-18a with #30 taper, great small foot print machine. Probably weighs as much as a BP though.
  7. Replies
    103
    Views
    6,382

    I’d grab a sack of toonies and beat the guy with...

    I’d grab a sack of toonies and beat the guy with the Craftex down.
  8. Replies
    103
    Views
    6,382

    15 hours one way let’s factor in fuel, hotel,...

    15 hours one way let’s factor in fuel, hotel, food and opportunity costs. What’s it really going to cost when it’s all said and done? Case in point when I got my first 10ee I could literally walk out...
  9. Replies
    103
    Views
    6,382

    The funny thing is I’m surprised this hasn’t...

    The funny thing is I’m surprised this hasn’t gotten locked yet.
  10. Replies
    103
    Views
    6,382

    [QUOTE=Terry Keeley;3315296]Yup!!! Check...

    [QUOTE=Terry Keeley;3315296]Yup!!!



    Check this out: Emco Maximat Super 11 Lathe | eBay

    Hmmm no tailstock in the pics and no mention of it. Just an observation.
  11. Replies
    103
    Views
    6,382

    That’s roughly $950 US and I’m sure you are in a...

    That’s roughly $950 US and I’m sure you are in a desert area for finding machinery. Not a whole lot of money to spend and I’m sure you’d get your money out of it if you didn’t like it. It’s by no...
  12. Replies
    103
    Views
    6,382

    If metric threading is important it has the...

    If metric threading is important it has the compound gear you see mounted, it’s the big one and there is at least one extra gear or maybe more in the plastic bag with the extra tooling.
  13. Replies
    5
    Views
    519

    I was pretty thorough in tracing the right wire...

    I was pretty thorough in tracing the right wire back through the cluster of wiring on the machine and of course I got it wrong with my temp line. Go figure. Thanks Tom.
  14. Replies
    5
    Views
    519

    Got things wired up and I can get it to run. I do...

    Got things wired up and I can get it to run. I do get some initial chattering in the magnetic starter. Originally it would cut out when either the high low switch or speed switch was operated to turn...
  15. Replies
    5
    Views
    519

    Thanks for getting back to me Ron. Having a bug...

    Thanks for getting back to me Ron. Having a bug up my .... I decided to check with a different multimeter This morning. I didn’t get anything between sets. Checked the original and now nothing at...
  16. Replies
    5
    Views
    519

    Issues testing two speed motor

    I recently picked up another orphan that was destined to be scrapped. Itís an index super 55 that hasnít run in 20+ years. After powering it up it was evident that there were issues electrically....
  17. Replies
    5
    Views
    1,169

    No specific plans other than where to put it. I...

    No specific plans other than where to put it. I may bring it home and put it in the basement, should work fine as it has a 3/4hp single phase on it. I would rather of had three phase and put a vfd on...
  18. Replies
    5
    Views
    1,169

    The problem is I reached my limit long ago and...

    The problem is I reached my limit long ago and may be considered a poacher at this point.
  19. Replies
    5
    Views
    1,169

    61 year old home shop J head

    Stumbled upon this Bridgeport and couldnít resist. All that was needed was a light cleaning and a new clogged belt. The belt shrank a bit and was quite stiff from lack of use and prevented it from...
  20. Well you got me thinking as I had some wiring...

    Well you got me thinking as I had some wiring issues with mine when I got it close to 10 years ago. It had a 480v 3p only motor which I changed to a standard dual voltage 3p motor.John Knox had...
  21. Iíd join the Sheldon group on yahoo. The Klockler...

    Iíd join the Sheldon group on yahoo. The Klockler Moeller motor that actuates the variable pitch pulleys is dc voltage. There should be a step down transformer for the 110v single phase that will go...
  22. Replies
    33
    Views
    5,265

    Hereís a few cartoons; Turned a piece down to...

    Hereís a few cartoons;

    Turned a piece down to 20mm to get the steady adjusted
    238299

    238296
    238297
    238298
  23. Replies
    33
    Views
    5,265

    Back to the resurrection

    Well itís been quite a bit but Iíve been able to get back to this project and make some headway. Iíve changed direction on the input shaft. I decided to weld up the end and rather than go to the...
  24. Replies
    2
    Views
    1,012

    Lathe has sold

    Lathe has sold
  25. Replies
    2
    Views
    1,012

    Sebastian Sheldon lathe 15x48

    Sebastian Sheldon B6 lathe with taper attachment and 4 jaw chuck. Bed has typical nicks but no obvious wear ridges, 8 speed gear head 35-910rpm 3hp 220v 3ph. Can operate both carriage feeds at the...
Results 1 to 25 of 271
Page 1 of 11 1 2 3 4