Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cole2534

Page 1 of 60 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    27
    Views
    1,223

    Teague Custom Marine? Sent via CNC 88HS

    Teague Custom Marine?

    Sent via CNC 88HS
  2. A member here recently picked up a J-head...

    A member here recently picked up a J-head bridgeport for $50. It was a cherry deal for sure, but the point is to keep looking for a real mill.

    Sent via CNC 88HS
  3. I bet that's a pain in the ass.

    I bet that's a pain in the ass.
  4. Looks like the ports have bushings in them, big...

    Looks like the ports have bushings in them, big ones. Pull those out and wiggle your finger around in there or a paper towel on wire, if it comes out rusty then dig deeper. Or an inspection mirror.
  5. Replies
    30
    Views
    1,195

    This is true. I have them for all of my rifles...

    This is true. I have them for all of my rifles and wouldn't go back to a bare muzzle unless I absolutely had to do so.

    It also helps new shooters to not develop a flinch since they attenuate...
  6. Replies
    30
    Views
    1,195

    So? Add a suppressor and it's even quieter. ...

    So? Add a suppressor and it's even quieter.

    Sent via CNC 88HS
  7. Thread: Dimple dies

    by Cole2534
    Replies
    5
    Views
    511

    Great info, thanks!

    Great info, thanks!
  8. Replies
    30
    Views
    1,195

    Because they improve the shooting experience for...

    Because they improve the shooting experience for everyone within 200yds.
  9. Replies
    30
    Views
    1,195

    Used PVS-30's were running 5-6k, KAC had a bunch...

    Used PVS-30's were running 5-6k, KAC had a bunch of refurbs from a .mil trade-in.

    Knights Armament PVS-30 Night Vision Unit. Like New; Grade A Reconditioned
  10. Replies
    25
    Views
    1,145

    Woof. Lotta shit there.

    Woof. Lotta shit there.
  11. Replies
    875
    Views
    35,252

    When you got a question, go to the source right?...

    When you got a question, go to the source right?

    Approaching with an air of arrogance tacitly begs for correction, make note then on to the next.

    Sent via CNC 88HS
  12. Great info, thank you. ^^^ That's why I love...

    Great info, thank you.

    ^^^ That's why I love this place.

    Sent via CNC 88HS
  13. Replies
    875
    Views
    35,252

    Based on his scams elsewhere, I'd suggest that...

    Based on his scams elsewhere, I'd suggest that this forum helped provide him the knowledge to pull the scams off. There's no way PM is liable or that we could have known, but its a great place to...
  14. Replies
    25
    Views
    1,145

    Lol what? Backstory please.

    Lol what? Backstory please.
  15. Thread: Dimple dies

    by Cole2534
    Replies
    5
    Views
    511

    I've got a whole pile of stressproof bar ends...

    I've got a whole pile of stressproof bar ends that'd be perfect.
  16. Replies
    13
    Views
    593

    That's some fancy stuff. Can you speak to what...

    That's some fancy stuff. Can you speak to what made that a requirement?
  17. Thread: Dimple dies

    by Cole2534
    Replies
    5
    Views
    511

    Dimple dies

    I want some dimple dies, and I'd prefer to to home brew them because I went from busy as hell to nada. Got the material (4140ph), time and tools.

    Flare looks about 30 degrees but I think that...
  18. I talked with those guys about a Mazak recently,...

    I talked with those guys about a Mazak recently, and they seemed like OK folks. The deal didn't go through so I don't have any experience beyond that.
  19. I didn't see where you mentioned a vintage, but...

    I didn't see where you mentioned a vintage, but if this shop is not under OSHA purview I'd go old enough to skip as much safety BS as possible.
  20. Replies
    7
    Views
    492

    John, how many #/ft does the extended length add?

    John, how many #/ft does the extended length add?
  21. Replies
    5
    Views
    389

    Ooof. Maybe some Starrett M1 instead.

    Ooof. Maybe some Starrett M1 instead.
  22. That's the kind of answer I was looking for. ...

    That's the kind of answer I was looking for. Thanks.
  23. I figured that was a given. I imagine the...

    I figured that was a given. I imagine the premium tools do work better to justify the cost, I'm just curious as how to they arrive there.
  24. What separates 'premium' carbide from 'commodity' carbide?

    As I dig deeper into tool choices, I'm left with the feeling that it's the base material that really makes the difference. There's only so many ways, albeit quite a few, that one can grind a 4fl...
  25. That's the truth.

    That's the truth.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4