Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: danil

Page 1 of 14 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    22
    Views
    1,763

    I have been surprised by what these 'hotshot'...

    I have been surprised by what these 'hotshot' load haulers are pulling with a 1 ton dually. Gooseneck trailers with tandem duals and 15,000# loads. I have a Dodge 3500 and would be worried about my...
  2. I'll stand in line in case they become available....

    I'll stand in line in case they become available. Thanks.

    Sent from my E6910 using Tapatalk
  3. Replies
    11
    Views
    1,218

    I buy from a company in Moraine, Ohio called...

    I buy from a company in Moraine, Ohio called Vibrodyne. They make electromagnetic tumblers.

    Sent from my E6910 using Tapatalk
  4. Replies
    19
    Views
    1,326

    All I run on laser is stainless.... it does...

    All I run on laser is stainless.... it does harden the edge on holes that are cut and dulls the countersink quicker than a punched/drilled hole. We had one vendor in particular for some reason had a...
  5. Okay, you have a buyer. Sent from my E6910...

    Okay, you have a buyer.

    Sent from my E6910 using Tapatalk
  6. Replies
    6
    Views
    1,188

    Curious... how thick of material are you...

    Curious... how thick of material are you notching? Notching is shearing. Shearing will push your upper blade away from the lower blade and put some side load on that cylinder on thicker material...
  7. Replies
    2
    Views
    959

    Looks like a copy of the Bock working unit.......

    Looks like a copy of the Bock working unit.... Bock got bought out a couple years ago by Jergens I think..

    Anyway, they work great as long as you take the time to square them up.

    Sent from my...
  8. Replies
    9
    Views
    595

    CNC cookbook also has a HP variable to set. ...

    CNC cookbook also has a HP variable to set.

    Sent from my E6910 using Tapatalk
  9. Replies
    9
    Views
    595

    My 'Happy Numbers' usually start with the CNC...

    My 'Happy Numbers' usually start with the CNC Cookbook. I like their G-Wizzard calculator which gives a nice tooling selection and speed and feed values with the ability to go from Conservative to...
  10. Replies
    7
    Views
    578

    My cnc roll bender requires me to scrap 5 pieces...

    My cnc roll bender requires me to scrap 5 pieces of each new material. Set the bender and record the result. Have the first and last close to or beyond your likely extremes. My machine calculates...
  11. I'd be punching the slots with a ironworker and...

    I'd be punching the slots with a ironworker and using either a stroke sander or belt sander to put a #4 brush finish on it.

    Sent from my E6910 using Tapatalk
  12. Replies
    3
    Views
    653

    I have to do this on my lathe, but it does...

    I have to do this on my lathe, but it does work(I'm going to double check, I'm thinking parameter 41).

    Anyway, have to do the same thing on the Haas Router.... only there is no door.
  13. Thread: OSHA results

    by danil
    Replies
    64
    Views
    8,299

    OSHA my way. OSHA is in place to protect our...

    OSHA my way.

    OSHA is in place to protect our workforce. I would substitute mandatory education and implementation of safety program in lieu of a fine for these first offenses(non-accident...
  14. Replies
    34
    Views
    2,886

    Question & suggestion

    Prudent suggestions so far.

    I'd like to know how deep this hole is? I'm drilling holes in 304 stainless 1-5/8 to 2-1/4" deep and would consider that pretty good for my application(.391 dia.). ...
  15. Replies
    24
    Views
    1,940

    I'm not sure if the previous post was referring...

    I'm not sure if the previous post was referring to the noramp.com no ramp trailers. They offer payload up to 15,000# in triple axle along with the standard tandem and single axle designs.
  16. Replies
    24
    Views
    1,940

    That ANTS trailer looks pretty interesting- and...

    That ANTS trailer looks pretty interesting- and perhaps simpler design. I have a JLG 248 which is the entry level version with a cable/winch raise/lower system. It works well for smaller loads like...
  17. If picture 24 D, the step drills are available,...

    If picture 24 D, the step drills are available, I'd take them.
  18. Thread: Gift--apron?

    by danil
    Replies
    14
    Views
    1,214

    Well Lörrach, I think we all should give you a...

    Well Lörrach, I think we all should give you a big round of applause. I'd think that once he learns that you signed up on the PM to get him a good gift that he'd feel like a pretty darn lucky guy!
    ...
  19. Thread: Shop advertising

    by danil
    Replies
    29
    Views
    2,303

    My experience has been best with the direct sales...

    My experience has been best with the direct sales call. Doesn't matter if it is a gated/guarded company, although a little more work involved. It all starts with a name... could be from the chamber...
  20. Replies
    55
    Views
    5,015

    Seems like every point I could have thought was...

    Seems like every point I could have thought was already debated. However, when I need a washer better than those standard zinc plated units I go with the Jergens Heavy Duty:
    Material: High Carbon...
  21. Replies
    63
    Views
    5,088

    Other guys have already addressed the biggest...

    Other guys have already addressed the biggest concerns.... I'm glad to see on the last post you are looking to pursue/integrate your stated strength in programming/machining. Seems to me a great...
  22. Replies
    14
    Views
    964

    I've been using the Microsol 585XT in my Fadal...

    I've been using the Microsol 585XT in my Fadal and been happy with it. My neighbor switched to it because he was getting rusty surfaces with his previous product and the 585XT eliminated that issue....
  23. Replies
    7
    Views
    1,165

    Safety First-- are those all Full Rev...

    Safety First-- are those all Full Rev Mechanicals? It seams only the 85 ton might be updated with an air clutch(but can't tell for sure without seeing the other side).

    Guarding becomes...
  24. Replies
    42
    Views
    4,384

    Looks great!.... and with that insulation the AC...

    Looks great!.... and with that insulation the AC won't cost much.

    Our plant has AC and it make these heat waves a non issue. I really like not having surface rust on everything, especially since...
  25. It looks fantastic, nicely done!

    It looks fantastic, nicely done!
Results 1 to 25 of 340
Page 1 of 14 1 2 3 4