Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Luke.kerbey

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    1,494

    Hi, The most we can do is clean the filter,...

    Hi,

    The most we can do is clean the filter, at the moment, of it persists in the future we can change the filter if needs be, we can see there is a blockage between the pump to filter line or the...
  2. Replies
    13
    Views
    1,494

    Jones and shipman universal grinder

    https://uploads.tapatalk-cdn.com/20190907/3c89e3d057e6147b3e7e82f6f8bc297f.jpghttps://uploads.tapatalk-cdn.com/20190907/95dd6106979c85d3953a08980b948ade.jpghttps://uploads.tapatalk-cdn.com/20190907/a7...
  3. Replies
    6
    Views
    798

    Wax spray, we use lusin protect g31 chem trend,...

    Wax spray, we use
    lusin protect g31 chem trend,
    Itís strong enough to stick when roughing on full power jet.

    But if your problem is from corrosion or pitting on surfaces created in that...
  4. Replies
    23
    Views
    1,858

    Yer, bolle is all Iíve used for 3 years, at cost...

    Yer, bolle is all Iíve used for 3 years, at cost of around £10 a pair every month, I just reckon I should more then 4 weeks from a pair that expensive.
  5. Replies
    23
    Views
    1,858

    Hey, thatís more like it, I found this article...

    Hey, thatís more like it, I found this article from uvex that says PC is an upgrade from CR34. Is this just their marketing?
    Also Iíd need the glasses for manual milling and turning too, so flying...
  6. Replies
    23
    Views
    1,858

    I fully appreciate that Iím asking for something...

    I fully appreciate that Iím asking for something that may not exist, but itís always worth asking!
  7. Replies
    23
    Views
    1,858

    Yer, me in an office 😂😂, if it doesn't have...

    Yer, me in an office 😂😂, if it doesn't have handles, Iím not touching it!

    So whatís the next step up from polycarbonate?
  8. Replies
    23
    Views
    1,858

    Wouldnít glass lenses be hardened and tempered...

    Wouldnít glass lenses be hardened and tempered like windscreens? So they canít shatter?

    I also get the issue with polymer remover melting the surface of the lens from splatters
  9. Replies
    23
    Views
    1,858

    Safety glasses!!!

    Hi,

    Iím looking for recommendations on safety glasses!

    I currently go through a set of polycarbonate glasses about every 4 weeks, as grinding dust and wheel dust scratches them so easily, I...
  10. Hi, I would be to happy proof read, my wife...

    Hi,

    I would be to happy proof read, my wife used to proof read political texts so she can give me a crash course on proofing and I can translate that to machining.

    Also Iíd be happy to take...
  11. Replies
    13
    Views
    1,494

    All I can start with is telling my boss that Iíve...

    All I can start with is telling my boss that Iíve done my research and sought advice, give him my prognosis based on this research and give him the options of,

    - me stripping the spindle out and...
  12. Replies
    13
    Views
    1,494

    Hi Robert, thanks for your time to reply, ...

    Hi Robert, thanks for your time to reply,

    Given all the technicalities of using a thermocouple and amp meter to help set the bearing clearances, is this something that a toolmaker could do?...
  13. Replies
    13
    Views
    1,494

    Hi, Thanks for that explanation, was easy to...

    Hi,

    Thanks for that explanation, was easy to understand, so does this mean that the seal may not need replacing? And this binding that is occurring, will it cause the bearing to need replacing? Or...
  14. Replies
    13
    Views
    1,494

    Jones and shipman universal grinder

    Has anyone got advice on how much damage is caused in our wheelhead?

    I switched on the machine last week and the wheel stalled after a couple minutes and the motor cut out, noticed the oil had...
  15. Have you got the right tool holders? We had a...

    Have you got the right tool holders?

    We had a similar problem when I started using a different set of tool holders on a TRAK knee mill, except the draw bar was too short, so we made a longer one.
  16. Replies
    8
    Views
    1,010

    If you can find a buyer why not?

    If you can find a buyer why not?
  17. Replies
    0
    Views
    335

    Hurco 900 generator wonít stay on

    Hi guys,

    Got a hurco 900 with 50/10 amp generator.

    Yesterday it was running all good and then a transistor blew which was shown by the transistor blown light. But because it was the prime 0.2...
  18. Replies
    6
    Views
    978

    My first mentor used to poor his cold milky tea...

    My first mentor used to poor his cold milky tea in the coolant. It used to develop this skin that was science experiment level.
  19. Replies
    11
    Views
    1,280

    Okay cool, there should be a combination of parts...

    Okay cool, there should be a combination of parts and adapters so you can mount the magnetic head on to the machine head. Then the chuck sticks to the magnet. Iím assuming the magnetic chuck has the...
  20. Replies
    11
    Views
    1,280

    You need a current 3R catalogue. They havenít...

    You need a current 3R catalogue. They havenít changed much in 40 years and all new gear is compatible with old.

    What systems do you have? 20mm diameter stems? Macro pallets?

    The mounting can...
  21. Replies
    12
    Views
    1,360

    The Agie form you speak of is actually two...

    The Agie form you speak of is actually two different machines. It used to be Agie and charmilles were different brands altogether but were bought by +GF+. The form 350 is most likely closely...
  22. Replies
    5
    Views
    703

    Chuck it in a 4 jaw independent or a face plate...

    Chuck it in a 4 jaw independent or a face plate if possible
  23. Replies
    6
    Views
    759

    Hi, If the user interface is similar to the...

    Hi,

    If the user interface is similar to the mondo, you can move the cursor to the top left corner to highlight the page number, then by pressing numbers 4 through 9 (press enter after each...
  24. Replies
    6
    Views
    759

    Is it a mondo or a mondo star? Or am I...

    Is it a mondo or a mondo star?

    Or am I thinking of the wrong machine?
  25. Replies
    2
    Views
    730

    All the machines Iíve used, the surface area that...

    All the machines Iíve used, the surface area that you give the machine is the size of the frontal electrode face. Usually in CM squared. Not the cavity size

    I take it your running a Agie machine...
Results 1 to 25 of 137
Page 1 of 6 1 2 3 4