Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: GENERALDISARRAY

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Wish it was closer,the last machine rescue road...

    Wish it was closer,the last machine rescue road trip nearly kilt me.
  2. Replies
    16
    Views
    891

    Unless that is a very new machine,and something...

    Unless that is a very new machine,and something has changed. Most lathes do not "rigid" tap with the lathe spindles. If you want to rigid tap on-center you will have to use an axial driven tool.
    ...
  3. Replies
    16
    Views
    891

    On-center tapping with the lathe spindles? Or...

    On-center tapping with the lathe spindles? Or driven tool tapping?
  4. Replies
    24
    Views
    1,180

    How handy On machines that will not handle a...

    How handy

    On machines that will not handle a null toolchange, I put a block delete in front of the Tx and M6 lines. That way during setup or program restarts there is an easy way to avoid an...
  5. Replies
    2
    Views
    289

    Can you please elaborate? I know on the mapps...

    Can you please elaborate?
    I know on the mapps machines, you had to change at least one parameter on a new machine to allow turning with Y off zero.
    In mapps, there was a parameter to allow...
  6. Australia has trees?

    Australia has trees?
  7. I think it says in the manual "the barfeed...

    I think it says in the manual
    "the barfeed signal is internally decoded, but external drivers are not supplied for it"
  8. OP you have mail

    OP you have mail
  9. The easiest way would be a timer relay inline...

    The easiest way would be a timer relay inline with the coil circuit of the chip conveyor contactor.

    To have it use a software timer during concurrent program execution would require it to be in...
  10. Replies
    4
    Views
    623

    Two cast parts located in fixture for secondary...

    Two cast parts located in fixture for secondary operations, no X,Y probing. But you get the idea.
    #501 and #502 are called with G68 at each operation for respective part.

    Weirdo Z values are...
  11. If I am understanding. Is the issue that you dont...

    If I am understanding. Is the issue that you dont have an accurate way to measure the TSC of the tapers?

    High Quality Precision Dimensional Inspection Gages

    model 77M with ball styli look on...
  12. Does it do this with a program resident in...

    Does it do this with a program resident in memory? Or only while DNC?
  13. Replies
    16
    Views
    6,946

    Let us know how that ends up. In Borat voice;...

    Let us know how that ends up.

    In Borat voice; You will never get this





    This would have been better with the spoiler tags, buy I couldn't get them to work.
  14. Replies
    32
    Views
    2,086

    mill a square hole? This sounds like a job for...

    mill a square hole? This sounds like a job for the Bridgeport.
  15. Replies
    6
    Views
    707

    We have a 17" Clausing Turn-nado. bought new...

    We have a 17" Clausing Turn-nado. bought new around 86. Not that old in my book. And Clausing still sells parts for this machine.

    I would investigate why it needs new spindle bearings before...
  16. I think there is a Kondia Supermill underneath.

    I think there is a Kondia Supermill underneath.
  17. Replies
    1
    Views
    420

    Everyone I know with the new HMI runs them in the...

    Everyone I know with the new HMI runs them in the maintenance/classic mode.
  18. Replies
    7
    Views
    769

    I spoke with Mike Hendricks in 2015 Technical...

    I spoke with Mike Hendricks in 2015
    Technical Service Specialist
    Phone: +1 704 927 8900

    like I said, he really helped us out.
  19. https://ebay.us/TMaHxQ $240 and 300% less...

    https://ebay.us/TMaHxQ

    $240 and 300% less mickey mouse
  20. Replies
    7
    Views
    769

    we have an Agie that is a little newer here, runs...

    we have an Agie that is a little newer here, runs DOS on a internal PC.

    Agie and Charmille are both serviced by George Fischer. I could not say enough good about the phone tech support they gave...
  21. all the jap machines that I know of use oil as...

    all the jap machines that I know of use oil as the medium for the thermal solution, like Velocite. Mori for several generations used velocite in the chillers and DTE light for the air-oil spindle...
  22. Replies
    11
    Views
    954

    Is it two hours north?

    Is it two hours north?
  23. need more input

    need more input
  24. Replies
    199
    Views
    8,642

    to be fair. Hardinge rode that 6T well beyond its...

    to be fair. Hardinge rode that 6T well beyond its heyday. I may be wrong but I recall seeing 87 vintage 4 axis superslants. I have a Miyano here that has a 0T-C and its a 89.The "dual path"...
  25. Replies
    199
    Views
    8,642

    yes and yes CNC and ROBODRILL Training...

    yes and yes

    CNC and ROBODRILL Training Schedule | FANUC America
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4