Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Harri89

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    160

    Pictures? Sounds like a machine full of...

    Pictures?

    Sounds like a machine full of problems and lack of maintenance.
  2. Replies
    7
    Views
    695

    OT! But, did that have the "snap set" manual...

    OT! But, did that have the "snap set" manual counters on those flat areas?
  3. Replies
    15
    Views
    9,287

    What is the meaning of tying the 6, 8 & 20...

    What is the meaning of tying the 6, 8 & 20 together at db25 end?
    I need to make a cable in few weeks, it it just linked togheter with cable pieces?
  4. Replies
    22
    Views
    2,620

    Good Job! Nice to hear you got her fixed :)...

    Good Job! Nice to hear you got her fixed :)
    Maybe you could upload some videos of this beauty running to YouTube and share the link here ;)?
  5. Replies
    22
    Views
    2,620

    Good looking machine! Would love to get more...

    Good looking machine! Would love to get more pictures of it and maybe later a video of it running!

    I hope you get it working :)
  6. Replies
    909
    Views
    72,382

    Is there enough meat on the right side of the...

    Is there enough meat on the right side of the gears smaller OD for a taperpin? If everyting else are working as they should and in good running condition. It could be the cure for now to get the...
  7. Thread: Labour of love

    by Harri89
    Replies
    6
    Views
    1,593

    More pics please :) From restoration too if you...

    More pics please :) From restoration too if you have :))

    Would Love to have that Rotary on my machine.
  8. That runout is quite much imo, should be like...

    That runout is quite much imo, should be like half of that or lower. It causes chatter in every machining operation as you say.

    Depends ofcourse how and where you measured the runout.


    How...
  9. Replies
    44
    Views
    4,295

    How accurate the lead-in distance "A" from middle...

    How accurate the lead-in distance "A" from middle to start point needs to be or does the control manage small errors itself?
  10. Replies
    44
    Views
    4,295

    Thank you for your answer didnt think it that way...

    Thank you for your answer didnt think it that way :)
    Next time, i will give this a try :)

    Do i program x/y to middle of the pocket before the lead in and the g41 x/y coordinates to midpoint of...
  11. Replies
    44
    Views
    4,295

    You can skip the g45/46/47 lead in/out by...

    You can skip the g45/46/47 lead in/out by pressing enter. The only lead in/out would be possible from inside the triangle, this pocket is inside a cylindrical piece of annealed 4140.

    And there is...
  12. Replies
    44
    Views
    4,295

    Heres my hand drawn sketches if anybody...

    Heres my hand drawn sketches if anybody understands of them anything....
    The smaller ones measurements are from bottom of a tcmt 11 insert. The bigger one is for the pocket.
    1, 2, 3 are the order...
  13. Replies
    44
    Views
    4,295

    I made an macro from the pocket and got it to...

    I made an macro from the pocket and got it to work with in feeds g91 and called g90 after that inside the macro. I still first had the same problem till i Figured out to write my Z2 position before...
  14. Replies
    44
    Views
    4,295

    If i do a macro/subroutine with g91 for the in...

    If i do a macro/subroutine with g91 for the in feeds example, do i have to call g90 again in the main program to stop g91 From the macro/sub?

    Would it be best to run the contour in a macro and do...
  15. Replies
    44
    Views
    4,295

    Was today doing some machining... Or atleast i...

    Was today doing some machining... Or atleast i tried, not with good succes..

    How do you write the program with the contour compensation on and infeed increments? (Example, 4x -z 3mm the same...
  16. Replies
    44
    Views
    4,295

    How does the G79 work? Does the control calculate...

    How does the G79 work? Does the control calculate on its own to clear out the excess material? (between contours/Islands in an pocket)

    What is the Allowances for length/radius in the Tool...
  17. Replies
    44
    Views
    4,295

    I use my old newbie thread :) Im going to mill...

    I use my old newbie thread :)

    Im going to mill a tool with insert pockets for tcmt 11 inserts. I have been thinking, what is the best method when it turns out to be abit small and i need To make...
  18. Replies
    21
    Views
    3,855

    I meant the microscope... The Rotary table can...

    I meant the microscope...

    The Rotary table can also be tilted In two directions??
  19. Replies
    21
    Views
    3,855

    greif1 thanks for the tip! Didnt think about that...

    greif1 thanks for the tip! Didnt think about that :)

    261131

    How should these be used properly?
  20. Replies
    21
    Views
    3,855

    Okay, i fixed the x-axis micrometer scale. There...

    Okay, i fixed the x-axis micrometer scale. There was a tiny spring disconnected. All seems working, its really dusty..

    How should the measuring with this kind of equipment be done since there is...
  21. Replies
    15
    Views
    1,701

    Wera has very good selection of screwdrivers, ...

    Wera has very good selection of screwdrivers, different sizes and shapes :)
  22. Replies
    21
    Views
    3,855

    I get this machine home tomorrow :) Lets see if i...

    I get this machine home tomorrow :) Lets see if i have time to upload few pictures before a vacation to Milano.
  23. Replies
    909
    Views
    72,382

    I i removed and installed all by myself with this...

    I i removed and installed all by myself with this crane. It had castors on each corner.
    I recommend to use a crane... Better to control the weight. You dont want any surprises and theres less room...
  24. Replies
    7
    Views
    2,084

    Surface Grinder table speed

    I have a Chevalier fsg-1224ad surface grinder with hydraulic table feed and automatic cross and downfeed.

    I have been grinding only some steel for now and it seems that when i take the last few...
  25. Replies
    21
    Views
    3,855

    Theres actually two Rotary tables in the picture,...

    Theres actually two Rotary tables in the picture, a small and simple one. Not so accurate. And the big one with higher accuracy. The big one has never been used. I have the accessories now at my...
Results 1 to 25 of 228
Page 1 of 10 1 2 3 4