Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cannonmn

Page 1 of 37 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    223

    Photo of tag

    Photo of tag
  2. Strange shell on Cinci mill crank, cause?

    At first the end of this side-crank for a Cinci horizontal mill appears to have a crack, however the apparent crack is only skin deep. The “skin” appears to be a completely separate outer layer of...
  3. Replies
    1
    Views
    223

    Need manuals OKK MH-3v vertical mill

    I see a guy on Eboo has parts manual for $95 but hope someone could get me the operator manual. I’ll wait on the parts one. I asked the US office of the company, they asked the Japanese office...
  4. Ok, need a bit more clarification; consider this...

    Ok, need a bit more clarification; consider this modern example: Sine Bar | 57-020-222 | Travers Tool Co., Inc.

    It is 10” x 1” x 1”. The only significant dimension where the old Taft-P. Bar...
  5. Thanks, I definitely want the clamp-to-side...

    Thanks, I definitely want the clamp-to-side capability, and that was at the root of my question. Was looking at how such a bar is clamped onto an angle iron at the complementary angle, which is then...
  6. Since these blocks are for use with 10” sine bar,...

    Since these blocks are for use with 10” sine bar, I’m going to buy one. The old style of sine bars, like this, TAFT PEIRCE SINE BAR 10" NO. 9116 10.000" CS-141-47 COMMERCIAL | eBay
    all seem to...
  7. Manual for Clutch brand pancake compressors?

    Friend wrote this:

    “I have a Clutch (Northern Tool), Chinese made, 110 volt, pancake compressor that is about 10 years old which is item number 1230060.?? I may have damaged it and/or my relief...
  8. Thanks, it could be the tires. I know one is bad...

    Thanks, it could be the tires. I know one is bad enuf that it gives a very rough ride, like it is completely flat on one side, big thump and bump every rotation. We’re going to have it replaced.
  9. Yes, 50 taper. Have some dials too, will look...

    Yes, 50 taper. Have some dials too, will look for the rear-end stuff. Bought a bunch of older stuff that was somewhat scattered among many boxes, so trying to put Humpty Dumpties together again.
  10. Replies
    5
    Views
    720

    Name and purpose of looong reamers?

    Two odd reamers came in with other odds and ends. What is common name, and typical application? They are about 24” long, didn’t measure diameter.
  11. Replies
    1
    Views
    532

    “EDM Dr.” small tap burner?

    Anyone have the manual for this? I have nothing to plug in to either round plug, don’t know what goes in them, so is it worth time fooling with this? I’m guessing not. I have larger tap burners so...
  12. “Besides that, I'd want to have a discussion with...

    “Besides that, I'd want to have a discussion with the person who would supervise me, and their boss. How expert are they at the craft? How supportive of your growth? Those discussions might be part...
  13. Source of cutters for Microbore R-302 boring head?

    Have the tool and some used cutters but would like to buy 2-4 new cutters for use on mild steel. Source? I spent considerable time websurfing but failed to find new or NOS ones.261470
  14. Thanks, I’ll put it next to the B&S Univ. no. 1. ...

    Thanks, I’ll put it next to the B&S Univ. no. 1. If anyone has a photo of the device complete with the angle stops, I’d like to see it. But replacing their function, not their form, sounds like...
  15. What’s missing from this B&S grinding fixture?

    If you can post a pic of a complete one, I’d appreciate it. Any literature? What’s proper name?
  16. Any idea how this screw-infested fixture was used?

    I have no idea because there doesn’t seem to be any way to work on the contents. Can’t weld, braze, Drill, mill etc. in there, as far as I can see.
  17. Replies
    3
    Views
    816

    Strange little bronze vise, purpose?

    Jaws look bronze, the rest steel. What are holes for? Purpose of vise? Is about 8” x 2” x 2”.

    261377
  18. Thx. The fork has been sitting in same spot for...

    Thx. The fork has been sitting in same spot for 2 mos. and this just began days ago. That’s strange but may be explained by the recent high temperatures (warehouse no A/C.). The hi temp was just...
  19. Asphalt-like stuff falling out of electric forklift!

    This is an older Crown 36-volt Forklift. It seems to be dropping asphalt-like grains on the floor. Has anyone seen anything like this? What causes it?
  20. So I ordered the one suggested by Sami. I...

    So I ordered the one suggested by Sami. I probably have a spare drawbar with the right threads, will check tomorrow. Thanks for all who helped with this.
  21. Many of these are marked Hardinge plus various...

    Many of these are marked Hardinge plus various cryptic numbers. Inside is straight, two diameters with 90 degree step. They must be for holding straight-shank tools as I think another suggested. ...
  22. Ok thx, I’d like to make sure this is the...

    Ok thx, I’d like to make sure this is the appropriate no-brainer, so sweat, no machine time solution for an extremely lazy person such as myself! I’ll put the ad here with my subtle highlight of the...
  23. Thx, sending pm req for info

    Thx, sending pm req for info
  24. Thanks, yes it looks like these are legs for a...

    Thanks, yes it looks like these are legs for a 10” base sine plate. 9 deg. G =1.569”; 40 deg. G =6.435”, both per HF digital caliper which happened to be close. The legs are a bit off (couldn’t be...
  25. Thanks much, picture rang a bell and I looked in...

    Thanks much, picture rang a bell and I looked in some boxes from same source and found the shafts in two separate boxes. Until your picture went up I had no idea of the rest of the parts and those...
Results 1 to 25 of 915
Page 1 of 37 1 2 3 4