Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: 1yesca

Page 1 of 21 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    549

    true but a bit of common seance would go a long...

    true but a bit of common seance would go a long way may be that it would be better suited for slotting screw heads not boiler plate machinist work one must know there limitation as well as the...
  2. Replies
    15
    Views
    549

    sharp eye there . i have a complete boxed...

    sharp eye there . i have a complete boxed horizontal set up and most of a second set up . i will get some pic of it and post . if i was going to keep it i would leave the horizontal motor base with...
  3. Replies
    21
    Views
    5,862

    the bearings are from a ford mod. A front axle...

    the bearings are from a ford mod. A front axle [spindle] or ford n8 tractor front axle [spindle] . when you dissemble the head stock [spindle ] be careful of the felt seals the two outer ones [vary...
  4. Replies
    15
    Views
    549

    # 2 M/T . true its no Bridgeport but for its size...

    # 2 M/T . true its no Bridgeport but for its size it was a well though out and built machine . thanks for looking .
  5. Replies
    15
    Views
    549

    getting there just need to dig out some tooling ...

    getting there just need to dig out some tooling




    319366319367319368
  6. Replies
    15
    Views
    549

    benchmaster mill

    has been setting for about 10 years i never used it so its time to go i . i took it completely apart [was gummed up ] cleaned and oiled every thing vary little wear org. paint the table is clean not...
  7. Replies
    21
    Views
    5,862

    old treat yes i know the spindle bearings are...

    old treat yes i know the spindle bearings are ford mod. A front wheel bearings also ford tractor n8 or n9 don't remember
  8. that casting on top of the headstock is cool get...

    that casting on top of the headstock is cool get rid of all that junk above it and install a 1 hp or 1-1/2 hp 3 ph motor with a vfd and go to town
  9. Replies
    9
    Views
    654

    look out or some one will try to tell you it...

    look out or some one will try to tell you it stuff your lathe dose not need so you should give or sell it to them but hey we suspect your a bit brighter then that . well maybe
  10. it may be time for another Battle of Athens, TN...

    it may be time for another Battle of Athens, TN 1946 for what they prevented in 46 is what happened in 2020 . to bad the likes of these heroes were not here in 2020 to stop the machine that gave us...
  11. bingo that dam play back button is dam near wore...

    bingo that dam play back button is dam near wore out on my machine just sounds like a blur . and the adults talking on the charily brown cartoons ya they nailed it .
  12. they say a picture is worth a 1000 words when i...

    they say a picture is worth a 1000 words when i was in 5th grade i love to get the popular electronics and copy the schematic . we had a set of world book encyclopedias i would sit for hours looking...
  13. yup it is a pita i read by memorizing the words...

    yup it is a pita i read by memorizing the words thank god for spell cheek i am more of a visual person and sound i love the sound of machines but if some brat is crying i am like a bull that see red...
  14. arp head studs and o ringing the heads goes a...

    arp head studs and o ringing the heads goes a long way but it's still a 6.0
  15. Replies
    45
    Views
    3,784

    yup the founders and ceo's of all them sites of...

    yup the founders and ceo's of all them sites of that like [ libtard] should be Fargoed [as in chipper]
  16. Replies
    30
    Views
    1,594

    or did it pan out for you

    or did it pan out for you
  17. Replies
    16
    Views
    665

    i just did a spindle change on a 10 heavy 1943...

    i just did a spindle change on a 10 heavy 1943 [from 1-7/8 to 2-1/4 ]and it had them brass wire clips did not know what they did or were for but i did make sure they went back in . now i know thanks...
  18. just sold something like that at about the same...

    just sold something like that at about the same price . someone is going to get a nice set up . good luck with your sale don't think it will last long before it get snapped up
  19. Replies
    14
    Views
    737

    years ago there was a used machinery sales that a...

    years ago there was a used machinery sales that a pal of mine from city collage worked at and on Saturday i would go there and he would let me dig in the scrap bin i learned a lot and i got a lot of...
  20. Replies
    43
    Views
    2,415

    dam and i was thinking it was the beginning of a...

    dam and i was thinking it was the beginning of a breech plug for a cannon tell i seen the other pic. with them threads at the end of that long shaft
  21. Replies
    10
    Views
    628

    so could one take so mono filament line from like...

    so could one take so mono filament line from like a weed wacker and and pack ?
  22. Replies
    53
    Views
    2,956

    tell then to go to home depot and get some all...

    tell then to go to home depot and get some all tread i worked for a guy and when people like that would come in with some off the wall b s he would just tell them [ i have enough real work to do ]
  23. that was living proof that rain man was alive and...

    that was living proof that rain man was alive and well more like ms. potato head
  24. the pet rock was one of the key factors in...

    the pet rock was one of the key factors in showing just how dumb most people are right up there with most sitcoms
  25. Replies
    71
    Views
    2,968

    so its not because of to meany u turns under the...

    so its not because of to meany u turns under the sheets
Results 1 to 25 of 512
Page 1 of 21 1 2 3 4