Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Harri89

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    204

    Cleaning the tachometer fixed the problem, how...

    Cleaning the tachometer fixed the problem, how crazy it sounds considering the symptom.


    Picture before cleaning. Nothing major dirt came off. Blew some Air and slowly fed z axis to get it to...
  2. Replies
    3
    Views
    204

    i was digging more PM and ill take a look at the...

    i was digging more PM and ill take a look at the servo tachometer tomorrow...
  3. Replies
    3
    Views
    204

    Deckel FP4A Z-axis Vibration

    Hi!

    Today was running program and everything worked like always.
    Suddenly the z axis did strange noise and whole machine vibrated when z axis did rapid motion.

    With feed it also moves jerky...
  4. Replies
    58
    Views
    7,262

    G2/3 with Z infeeds doesnt work, 3 axis...

    G2/3 with Z infeeds doesnt work, 3 axis simultaneous linear moves are possible. Kind of stupid since it has a canned cycle for threads etc. Or is possible to do helical moves with G9 code?
  5. Replies
    7
    Views
    503

    Its a picture from my cad model, ive made now one...

    Its a picture from my cad model, ive made now one part and feeds/speeds need some tweaking and need to change few dimensions.
  6. Replies
    7
    Views
    503

    Heres a picture of the pocket. Its first roughed...

    Heres a picture of the pocket. Its first roughed with straight end mill to near top of the insert pocket. Then the sides are finished to size with tapered end mill and after that the insert pocket is...
  7. Replies
    7
    Views
    503

    The pocket where the insert pocket is, has also...

    The pocket where the insert pocket is, has also 7degree walls, but its larger at bottom than the top of the insert pocket.

    So when the taper endmill is side milling, its using 2.5mm to close to...
  8. Replies
    58
    Views
    7,262

    I try to check these today, i have coolant...

    I try to check these today, i have coolant disabled from the CAM, but i also wonder why M9 is double. I am again very thankful for your input :)
  9. Replies
    7
    Views
    503

    Cutting data for Tapered End mill

    Hi!

    I side mill to ~ 20mm depth after end mill have roughed out the pocket, at the bottom i machine a pocket for TCMT11 insert.

    I have a TCE brand 7 degree tapered end mill with 2.5mm tip and...
  10. Replies
    58
    Views
    7,262

    Here is an example of the code, how it should be...

    Here is an example of the code, how it should be to work with deckel?

    %
    (&%10/000000)
    N1 M9
    N2 G0 Z100
    N3 G17 T5
    N4 S+1200 G4 F1.0
    N5 M9
    N6 G0 X10.402 Y-11.629
  11. Replies
    58
    Views
    7,262

    So i would need to get my fusion 360 post...

    So i would need to get my fusion 360 post processor modified so that z moves are done in separate block?
  12. Replies
    58
    Views
    7,262

    I had at last some time to play with Fusion 360...

    I had at last some time to play with Fusion 360 and had my first program successfully loaded to my deckel. Now i had error 93 with some of the blocks and those blocks contains g2/3 with Z move......
  13. The commutator looked OK, for what you can see...

    The commutator looked OK, for what you can see from the brush holder hole with light..

    It has an optical shaft encoder. Theres info in the picture attached.

    What to be aware of if i open the...
  14. Carbon brushes were OK and seemed to move freely....

    Carbon brushes were OK and seemed to move freely. I pulled the motor out and ran it for while in both direction. Since its a tilting axis the motor doenst ever get to run so much. The sound changed...
  15. Brushes was ok, i used air to clean the brush...

    Brushes was ok, i used air to clean the brush holders. There were almost any carbon dust.

    I changed parameter 215 from 30 to 15 and parameter 214 from 1200 to 1500. I made the changes with 5 and...
  16. I know that the motor have brushes

    I know that the motor have brushes
  17. I have been trying to search info for the...

    I have been trying to search info for the parameters. They seem to be different than usually.

    If i load the motor with a lever inside the rotary through hole and jog the tilt axis, the 2102 error...
  18. Nikken 5ax-120 Servo motor noise and alarm

    Hi!

    I have been trying to get my Nikken 5ax-120wa rotary table to work. Its with Alpha control and own control box for rotary and tilting axis.

    I have the parameters set to them and everything...
  19. Replies
    4
    Views
    707

    My machine has a plate on the knee which says...

    My machine has a plate on the knee which says "14.2kg/cm2"
    Its ~ 14bar, i adjusted it little over and the speed change seemed to work better.

    282336
  20. You can also turn the thread with lathe to get it...

    You can also turn the thread with lathe to get it uniform. I had my mill y axis lead screw fixed this way. Then made a new thread cutting hss bit to match the "new" thread of the screw and turned new...
  21. Replies
    4
    Views
    707

    Are yöu sure the motor overload protection is...

    Are yöu sure the motor overload protection is adjusted too low and cutting the current?

    Heres a picture of hydraulic diagram for cinedo. It has something about the pulses.
    281895
  22. Replies
    5
    Views
    851

    Would be nice to see closer the grinding head :)

    Would be nice to see closer the grinding head :)
  23. Thread: Okk mh-3pii

    by Harri89
    Replies
    10
    Views
    601

    Thats really rigid looking machine! Ive only seen...

    Thats really rigid looking machine! Ive only seen them on pictures and youtube. Would want one for my collection :nutter::D
  24. Do not hammer / push it from behind! You need to...

    Do not hammer / push it from behind! You need to remove the worm from the worm wheel first. Else you might bend the shaft or damage them.
  25. Replies
    58
    Views
    7,262

    Do someone know what software update version is...

    Do someone know what software update version is neesded to get this work whats shown in picture?
    Atleast cant get it to work, gives error 81 if i remember correct.

    Is there a way to update this...
Results 1 to 25 of 318
Page 1 of 13 1 2 3 4