Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Speedie

Page 1 of 55 1 2 3 4

Search: Search took 0.02 seconds; generated 22 minute(s) ago.

  1. Replies
    28
    Views
    2,925

    Warming up a spindle has little to do with the...

    Warming up a spindle has little to do with the bearings and more to do with what the spindle casing has to do with the bearings. Once you take and reduce the radial load on the bearings by heating...
  2. Replies
    4
    Views
    415

    Haas really doesnt have a great chip solution...

    Haas really doesnt have a great chip solution IMO. The single auger just rolls big bats of chips until they get stuck in the corner. The quad doesnt have the angles steep enough to move the chips so...
  3. Replies
    27
    Views
    2,325

    I only tap on the weekends and holidays. Very...

    I only tap on the weekends and holidays. Very sober at work breaking all those threading tools
  4. Replies
    38
    Views
    2,830

    Bore is different than drilled. Sure you can i...

    Bore is different than drilled. Sure you can i spect a drilled hole but you certainly cannot metric a machines accuracy by it that is just sloppy metrology
  5. Replies
    38
    Views
    2,830

    Well I wondered how the OP drilled holes abd saw...

    Well I wondered how the OP drilled holes abd saw they were off by .002...was this with a drill bit and what did he expect...lol. You cant gauge a fucking hole from the end of a drilled hole.
  6. Replies
    28
    Views
    1,974

    There are only a few companies that specialize in...

    There are only a few companies that specialize in cutters that big. All BS and feelings aside. Your best bet is to explore the geometry of the insert pockets and look up geometry for them.
  7. Replies
    8
    Views
    1,072

    Curious how you do this since they can move...

    Curious how you do this since they can move slightly on power down.
  8. Do you have a huge stupid nose radius??

    Do you have a huge stupid nose radius??
  9. Replies
    103
    Views
    8,126

    Just dont ever plan on going out of business as...

    Just dont ever plan on going out of business as part of your business plan. Be a good planboy
  10. Replies
    103
    Views
    8,126

    You sure can turn the spindle on with the door...

    You sure can turn the spindle on with the door open on a new haas. You can jog..ect too. Spindle rpm is limited to 750 until you close the doors. Actually when you run a new SS it is 10 times...
  11. Replies
    28
    Views
    2,925

    You will heat that grease in the bearing in less...

    You will heat that grease in the bearing in less than a minute and keeping the oil from the soaping agent has everything to do with keeping the bearing rotating.
  12. Replies
    6
    Views
    724

    A good mist collector properly sized will not...

    A good mist collector properly sized will not send any mist in the shop air. I have seen a shop full of TSC machines buzzing...all LNS mist collectors and the air was wonderful...floor was white....
  13. It has 30 percent more power than a Haas and 30k...

    It has 30 percent more power than a Haas and 30k more for the spindle. Man Haas looks like a crazy good value
  14. Replies
    19
    Views
    3,483

    Place I was at bought 2 new vf4ss in 2018..they...

    Place I was at bought 2 new vf4ss in 2018..they were real good machines and still perform. You cant go wrong with Haas.

    You can go very right
  15. Replies
    9
    Views
    692

    Fadal st torque machines will not even come close...

    Fadal st torque machines will not even come close to handling a 3/4 emill ..3/4 deep in aluminum at any decent feedrate over 20ipm. The high torque is a different story.
  16. Who makes a good ferrrous manual and auto cold saw??

    Cannot seem to locate a good cnc and non cnc saw. Was told to seek out both. Its like its a big damn secret. Everything I pull up is non ferrous
  17. The future does not include the caterpillar taper...

    The future does not include the caterpillar taper in my opinion. It may include variants of the taper but todays 30 taper spindles have a retention knob that limits virtually all other factors. Is...
  18. Replies
    12
    Views
    2,208

    Ze passion to sell U used has no confines Misssuer

    Ze passion to sell U used has no confines Misssuer
  19. Replies
    12
    Views
    2,208

    I wished used machinery selling wasn't such a cat...

    I wished used machinery selling wasn't such a cat and mouse sport. Used machinery dealers (Virtually 100% of them) never even turn a machine on or check it. They simply market a machine. Cant blame...
  20. Replies
    13
    Views
    1,217

    10k 15 always had an extra pump for spindle...

    10k 15 always had an extra pump for spindle chilling
  21. Thats like any given monday for the gifted in us...

    Thats like any given monday for the gifted in us all. Get some slow motion crash videos for the masses. That would be spectacular. Take it with a grain of salt and keep your passion youngster
  22. Replies
    37
    Views
    3,666

    Peck drilling can be a disaster for larger...

    Peck drilling can be a disaster for larger insertable drills. Shock loading the inserts can break them. Peck drilling is an age old way of getting coolant in and chips out but not applications should...
  23. Replies
    7
    Views
    827

    LOTSA HIGH FREQUENCY! What did I win?

    LOTSA HIGH FREQUENCY! What did I win?
  24. Replies
    144
    Views
    12,845

    Backup.... Le passione!!

    Backup.... Le passione!!
  25. Where are you located. I know of a guy with a...

    Where are you located. I know of a guy with a fadal 6030 with a 4th axis. Wants 14k for it in western wisconsin.
Results 1 to 25 of 1353
Page 1 of 55 1 2 3 4