Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: mTeryk

Page 1 of 35 1 2 3 4

Search: Search took 0.01 seconds.

  1. Sargon is standard quadrature encoding. Pinout is...

    Sargon is standard quadrature encoding. Pinout is different, yes. I've adapted Sargon scales to work on other DRO's before. The ones I had used a DB-25 connector. Wasn't hard to figure out what was...
  2. Replies
    37
    Views
    2,182

    Reverse that. Feeding in the compound, when set...

    Reverse that. Feeding in the compound, when set parallel to Z, will adjust timing.

    Good idea to use a dial indicator to track the location of the compound. That way you can move back and forth...
  3. Everything sold a long time ago. Sent from my...

    Everything sold a long time ago.

    Sent from my XT1710-02 using Tapatalk
  4. Wish you weren't so far away. I've been looking...

    Wish you weren't so far away. I've been looking for one of those.

    Teryk

    Sent from my XT1710-02 using Tapatalk
  5. That like like an nmtb40 to me. Sent from my...

    That like like an nmtb40 to me.

    Sent from my XT1710-02 using Tapatalk
  6. Thread: Advice please

    by mTeryk
    Replies
    6
    Views
    660

    I have some advise. Change your thread title so...

    I have some advise. Change your thread title so people reading it have some idea about the content of the thread and your question.

    The world's most knowledgeable person on your exact control...
  7. From the SDS for the product you linked: ...

    From the SDS for the product you linked:



    Sent from my XT1710-02 using Tapatalk
  8. Replies
    55
    Views
    2,616

    I have to get to work so this isn't super...

    I have to get to work so this isn't super detailed but it should get you started. You'll have to look up some resources on geometry and trig to get more info. I suggest the Khan Academy. He does a...
  9. Replies
    5
    Views
    630

    Only two US based manufacturers of size I know of...

    Only two US based manufacturers of size I know of are Rolf Prima and Velocity. I'm sure you could get contact information off of their websites. I used to work closely with Rolf Prima, if you have...
  10. I haven't seen Edge Precision, but This Old Tony...

    I haven't seen Edge Precision, but This Old Tony is hilarious and his level of production is super high. His camera work and editing are better than any other YouTube machinist except for maybe...
  11. Replies
    925
    Views
    77,841

    I used to use Koolmist but have found it rusts my...

    I used to use Koolmist but have found it rusts my tables and vises unless thoroughly cleaned and dried after every use (including pulling the vises). Kind of a pain the way I use my mills.

    I now...
  12. Replies
    12
    Views
    1,260

    Second on the #39, if it doesn't work out. ...

    Second on the #39, if it doesn't work out.

    Sent from my XT1710-02 using Tapatalk
  13. Replies
    1,219
    Views
    78,537

    This blog post reports a ton of data on the Model...

    This blog post reports a ton of data on the Model S battery life which seems much better than you write. There were major improvements in the Model 3 battery so one would assume it to be the same or...
  14. I do not have experience with Singer's pull...

    I do not have experience with Singer's pull studs, myself. As to why they don't pull out when unscrewing the draw bar, I think it has to do with the asymmetrical buttress thread form. They provide a...
  15. Mostly agreeing with Andy. In the states CAT40 is...

    Mostly agreeing with Andy. In the states CAT40 is probably the most readily available tooling that easily adapts to your mill. I'd leave the drawbar alone so you can use Deckel tooling and get the...
  16. Nope, I do have a 40 taper to R8 adapter kicking...

    Nope, I do have a 40 taper to R8 adapter kicking around. Tons of stickout, though, think you'd be over a foot of stickout if you were to use it with this head.

    Teryk


    Sent from my XT1710-02...
  17. Replies
    46
    Views
    3,359

    I don't think "Shipped by Amazon" says anything...

    I don't think "Shipped by Amazon" says anything about the authenticity of a product. If you do a web search you will find much discussion of Amazon's fraud problem.

    If you look at the Amazon...
  18. I'm curious what people think these are worth?. ...

    I'm curious what people think these are worth?.

    I've got one in a wood case with an SK40 mount, the power supply and a bunch of arbors and collets. I contacted the company to see about getting a...
  19. I imagine you would be keeping the cabinet even...

    I imagine you would be keeping the cabinet even if you were going to retrofit but if not, I'd be interested in it. Not the PC just the cabinet as I'd like to downsize mine.

    Teryk

    Sent from my...
  20. Replies
    29
    Views
    2,332

    I always conventional mill at full depth with a...

    I always conventional mill at full depth with a slitting saw.

    Sent from my XT1710-02 using Tapatalk
  21. Replies
    28
    Views
    2,244

    Dnc4u can be helpful in this regard. It will...

    Dnc4u can be helpful in this regard. It will listen in on a parallel port and configure your settings for you. I haven't tried it but you might be able to loop the port as described above and then...
  22. Replies
    8
    Views
    1,265

    Don't see how that math works out. Sent...

    Don't see how that math works out.



    Sent from my XT1710-02 using Tapatalk
  23. Welding Tips and Tricks - TIG, MIG, Stick and a...

    Welding Tips and Tricks - TIG, MIG, Stick and a pantload of other info

    Jody knows his stuff and is a really good teacher.

    Edit: name wrong

    Sent from my XT1710-02 using Tapatalk
  24. Don't have much to add other than that I helped a...

    Don't have much to add other than that I helped a friend set one up and flipped through his programing manual when doing so. Seemed to have a bunch of built in 3D surfacing routines.

    Doubt they...
  25. Replies
    21
    Views
    1,574

    +1 on the Dynasty 200. I've welded quite a bit of...

    +1 on the Dynasty 200. I've welded quite a bit of aluminum with an air-cooled torch with it, although mostly thinner stuff. It will run off of 110v without complaint but don't think I'd try aluminum...
Results 1 to 25 of 861
Page 1 of 35 1 2 3 4