Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cal Haines

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    28
    Views
    1,227

    I don't know what happened, but give them another...

    I don't know what happened, but give them another call. They'll take care of you.

    Cal
  2. Personally, I would steer away from anything that...

    Personally, I would steer away from anything that involves modifying the machine itself. If you drill out the bearing block for larger bolts, you'll eventually need to replace it. A solution that...
  3. https://www.practicalmachinist.com/vb/attachments/...

    https://www.practicalmachinist.com/vb/attachments/f10/329553d1631937946-resurrecting-1960-10ee-460v-sabina-drive-electrical-layout.jpg
    The Jefferson Electric "Powerformer" 3R is a 1:10 step up/down...
  4. Replies
    28
    Views
    1,227

    The problem is definitely with the generator's...

    The problem is definitely with the generator's brushes. It could be brush tension, but most likely the brushes are just worn out. You can order a full set of brushes form Monarch. At last report...
  5. Replies
    28
    Views
    1,227

    The two big relays/contactors that are sitting...

    The two big relays/contactors that are sitting side-by-side are the forward (F) and reverse (R) contactors. The relays at the top won't cause the symptom that your describing. Post a photo or two...
  6. Replies
    28
    Views
    1,227

    The DC panel looks OK, no obvious problems in...

    The DC panel looks OK, no obvious problems in that photo. Can you post a photo of the contacts that you're concerned about? Would you be able to get to the terminals at the bottom of the DC panel to...
  7. Replies
    28
    Views
    1,227

    Please post photos of the inside of the DC...

    Please post photos of the inside of the DC control panel (the big box full of relays, next to the spindle motor) and the tailstock-end of the motor/generator (MG), assuming that's the type of drive...
  8. I can rename the thread for you. I would go with...

    I can rename the thread for you. I would go with something like: "EE12345 195X with Sabina 440V DC drive". What's the serial number and build date of the machine?

    As far as powering it goes, you...
  9. Replies
    25
    Views
    1,153

    You photos are posting very small. Make sure you...

    You photos are posting very small. Make sure you change the file extension from JPEG to JPG before posting, so that they will come in at a decent size.

    Cal
  10. Replies
    4
    Views
    380

    I know people have used serpentine belts for the...

    I know people have used serpentine belts for the feed-belt, but I don't recall them being used for the main drive belt. If your machine is like my flat-belt machine, I'm not sure one would work. My...
  11. Just stick to helping people, sharing information...

    Just stick to helping people, sharing information and you're good. Personal attacks will be deleted; it's not personal.

    Cal
  12. I added the link to the post. Cal

    I added the link to the post.

    Cal
  13. Replies
    49
    Views
    3,130

    Thanks! That's very interesting. I assume that...

    Thanks! That's very interesting.

    I assume that instead of the inexpensive, cable-type come-along, you were using the chain-type, like this: link

    I'm not exactly sure what you mean by "chokered"...
  14. Replies
    220
    Views
    20,169

    I repaired my pumped lube system but also added...

    I repaired my pumped lube system but also added ball oilers to my saddle as a backup: OzEE rebuild

    Cal
  15. Replies
    49
    Views
    3,130

    https://www.practicalmachinist.com/vb/attachments/...

    https://www.practicalmachinist.com/vb/attachments/f10/327581d1629680602-my-10ee-some-shop-pictures-img_0084.jpg

    OK, NOW I get it!. I thought the expansion joints were under the angle, not...
  16. Replies
    49
    Views
    3,130

    https://www.practicalmachinist.com/vb/attachments/...

    https://www.practicalmachinist.com/vb/attachments/f10/327320d1629329826-my-10ee-some-shop-pictures-img_0059.jpg

    Thanks for sharing these!

    Let me see if I understand what you did with the angle...
  17. Replies
    40
    Views
    2,237

    Look at the round vent hole on the back. If it...

    Look at the round vent hole on the back. If it was cast, not cut by hand, it was probably a WiaD base at least. I have seen one former MG machine that was retrofitted with a WiaD drive.

    If the...
  18. Replies
    6
    Views
    563

    In Joe's post, he relates some of his experience...

    In Joe's post, he relates some of his experience with lubricating machines:

    He then goes on to say that because DTE 46 or DTE 68 worked for large turbines, it should be fine for machine tools. He...
  19. Replies
    16
    Views
    1,329

    Good idea. Rather than another sticky, it...

    Good idea. Rather than another sticky, it probably belongs in the General Information sticky.

    Are you volunteering?

    Cal
  20. It IS the telescoping type. You can see the...

    It IS the telescoping type. You can see the bearing block (EE-1592) in the video; if this were the standard cross-feed screw, you would see the end of the screw sticking out. Only telescoping...
  21. https://www.practicalmachinist.com/vb/attachments/...

    https://www.practicalmachinist.com/vb/attachments/f10/326883d1628839090-10ee-potential-purchase-img_3826.jpg

    What you're calling the "attaching bar" is correctly called the "Draw Bar" (part...
  22. Replies
    8
    Views
    679

    My '43 10EE has all CI covers. Most are stamped...

    My '43 10EE has all CI covers. Most are stamped with the 5-digit serial number on one of the machined surfaces. But I'm sure that varied a lot over time, etc.

    Cal
  23. You probably just need to change the file...

    You probably just need to change the file extension on the photos from ".JPEG" to ".JPG". See note in the forum rules.

    Cal
  24. You could try using the forum search tool (link...

    You could try using the forum search tool (link) to search the Monarch forum for posts by peterh5322 and jump backwards until you get to posts prior to that one.

    In theory, this Google search...
  25. Replies
    8
    Views
    679

    Jim, Thanks for posting those casting numbers...

    Jim,

    Thanks for posting those casting numbers and photos!

    Out of curiosity, where did you find them?

    Cal
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4