Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: sudsy55

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds; generated 4 minute(s) ago.

  1. Replies
    5
    Views
    328

    How long has the machine been sitting? If...

    How long has the machine been sitting? If batteries have gone flat and parameters lost you may need to do a re-initialise. Check parameters as has been mentioned before anything else.
  2. Replies
    3
    Views
    205

    First thing to check is the capacitors. Change...

    First thing to check is the capacitors. Change the lot would probably be best. Only get good quality name brand ones as some of the cheap ones aren't much chop. I get a lot of stuff from here...
  3. Maybe go through the parameters you have with...

    Maybe go through the parameters you have with what the EEprom loaded and make the changes to your hard copy for the future
  4. Replies
    14
    Views
    629

    Yes I get that often if I have been doing a lot...

    Yes I get that often if I have been doing a lot of editing in a program. I only try it a couple of times then just rewrite that unit and 9 times out of 10 it fixes the problem
  5. Replies
    1
    Views
    367

    Modify the pump to take a readily available seal

    Modify the pump to take a readily available seal
  6. Replies
    0
    Views
    366

    Probe problem on H 400

    G'day all, trying to get the probe working on my H400. It had a probe setup already but the induction module had been crashed into prior to me buying the machine so I've never had a probe working on...
  7. Replies
    2
    Views
    583

    Shame the shipping to Australia is so bloody...

    Shame the shipping to Australia is so bloody expensive
  8. Not that I have found but maybe someone that has...

    Not that I have found but maybe someone that has had proper training may know. I am pretty much self taught so still very green
  9. Use your edge finder and take it to the X...

    Use your edge finder and take it to the X coordinate of your job. On the command screen look at the numbers for the X position. This is your X zero + or - half the diameter of the edge finder. This...
  10. You'll work it out in no time Mick. I'm only a ph...

    You'll work it out in no time Mick. I'm only a ph call away to get you started. Or I might come for a bit of a ride lol
  11. I think you've confused everyone with these old...

    I think you've confused everyone with these old machines Mick lol
  12. Are you getting any errors or does it just...

    Are you getting any errors or does it just unclamp and sit there? If just sitting there you need to check if its getting the index signal. Should be able to see this on the ladder
  13. How did you go? Get it sorted?

    How did you go? Get it sorted?
  14. Replies
    20
    Views
    2,164

    Might pay to flip the breakers off then back on....

    Might pay to flip the breakers off then back on. Some types of breakers can look like they are on but have actually tripped
  15. Replies
    17
    Views
    2,085

    Actually I think there is an epprom you will need...

    Actually I think there is an epprom you will need but after that the other options may be just parameter related. It is on the memory modules (lower left side of controller. I can't remember the...
  16. Replies
    17
    Views
    2,085

    Knowing what they're like there is probably...

    Knowing what they're like there is probably another secret code you need to get into it. Try rubbing your belly clockwise, your head ccw while standing on one leg on a bungy cord in the middle of the...
  17. Replies
    17
    Views
    2,085

    Interesting to see the outcome

    Interesting to see the outcome
  18. Replies
    4
    Views
    963

    And I do that how exactly???

    And I do that how exactly???
  19. Replies
    4
    Views
    963

    I have tried all different combinations. Changed...

    I have tried all different combinations. Changed a couple of parameters associated to chamfering and still the same
  20. Press MNT PressPLC PressPREG Pressthe clear...

    Press MNT
    PressPLC
    PressPREG
    Pressthe clear key once (top rh corner} (this puts the keypad in letter mode)
    Press 6 9That should give you ( R) in the brackets at the bottom
    Punch in 2390 (this...
  21. You press the management button then go to PLC I...

    You press the management button then go to PLC I think. Will check tomorrow
  22. Change it with machine running is the best but...

    Change it with machine running is the best but can be done with machine off if you get it done in short time
  23. These are the parameters on my H400 so I don't...

    These are the parameters on my H400 so I don't know if yours would be the same but being M32 I would say they should be the ones.R2390is the distance between the switch signals. You will have to...
  24. Replies
    4
    Views
    963

    Doing my head in

    G'day all,
    have just recently started working my H400 with M32 controller. I'm having trouble getting the chamfer program to work. Have tried different size tools and adjusted a couple of...
  25. Its done in the R parameters. Not in the shed at...

    Its done in the R parameters. Not in the shed at the moment so not sure which one offhand. Takes a little bit of mucking around and measuring but not too difficult
Results 1 to 25 of 421
Page 1 of 17 1 2 3 4