Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thanks a lott Now I am puzzled what their scam...

    Thanks a lott
    Now I am puzzled what their scam is ???

    Peter
  2. MMmmmm They came back on me Basicly said ...

    MMmmmm
    They came back on me
    Basicly said

    That is wierd As a L/C costs about a €1000 more or less And that for the 30% balance
    Asked them what their conditions were for the L/C

    Then...
  3. Replies
    36
    Views
    2,497

    Off coarse the deriver iver is responsable He is...

    Off coarse the deriver iver is responsable He is the one who has to secure the load He is legaly obligated Over here it is regulated how many straps on how heavy a load is Here a load is automaticly...
  4. Replies
    28
    Views
    1,894

    I did ask him who bought his machines and why He...

    I did ask him who bought his machines and why He told me his machines are used as manual hard turning machines
    Many of his customers are in the optical industrie As a example he told me of a...
  5. Replies
    28
    Views
    1,894

    The ruemema route will cost him about €50000 to...

    The ruemema route will cost him about €50000 to €60000 if not more
    He does not restore these for stock anymore Only if ordered And his prices went way up

    Peter
  6. Perhaps put it in star and tell your VFD it is a...

    Perhaps put it in star and tell your VFD it is a 50Hz motor and then set it to 60 Hz

    Peter
  7. This is correct if you have a motor with 6 leads ...

    This is correct if you have a motor with 6 leads and the higher voltage is 1.73 x lower voltage Very common here Not so much in the US
    Here the motors are 220/380 volts Not 220/440 So...
  8. Replies
    28
    Views
    1,894

    Amazing how acurate his machines are Saw him...

    Amazing how acurate his machines are
    Saw him taking the measurement on a Leinen There was 1 measurement that was 0.003mm off The rest all better
    There were 3 that were less as 0.0005mm

    Peter
  9. According the plate this is not a dual speed...

    According the plate this is not a dual speed motor Dual voltage yes The motor can be used at 50 or 60 hz
    With 50 hz it runs 1500 rpm With 60 hz it runs 1800 hz

    Peter
  10. You can design a forklift chassid massifly...

    You can design a forklift chassid massifly because there are no weight restrictions
    You have to ad weigt anyhow
    Peter
  11. Dual speed motor perhaps?? Instead of dual...

    Dual speed motor perhaps?? Instead of dual voltage ??

    Peter
  12. I agree If is is a special motor (wierd...

    I agree
    If is is a special motor (wierd flangemotor for example)I would investigate if it could be rewound for 240volts

    Peter
  13. Reverse IP shows 3 websites of which 2 are in...

    Reverse IP shows 3 websites of which 2 are in Lagos Nigeria
    Scam for sure
    As I told them in my last e-mail that machines do not leave my warehouse before it is payed for in full in irreversable...
  14. The google streetview is from 2019 And I do not...

    The google streetview is from 2019 And I do not see that address listed at the Rexnord website any more

    Peter
  15. Information about a compagnie needed

    Anyone know this company
    Addax Industrial Machinery Inc.
    4701 Greenfield Ave,
    Milwaukee, 53214
    Wisconsin,
    ADDAX INDUSTRIAL MACHINERY INC | Home


    Bill is the one I had a...
  16. Replies
    28
    Views
    1,894

    I double your money :D For spares you could...

    I double your money :D

    For spares you could also ask Ruemema
    Drehmaschinen von Ruemema
    He is one of 2 I am aware of that is capable of rebuilding a 135 to original or better specs Also a very...
  17. On many machines ,Schaublin and Weiler to mention...

    On many machines ,Schaublin and Weiler to mention 2 ,a clamp can be used to keep the chuck on when turning in revers
    Attached a picture of one
    339780
    The sleeves in the flangebody you do not...
  18. Replies
    36
    Views
    2,497

    That pallet is too flimsy to be helpfull I...

    That pallet is too flimsy to be helpfull
    I prefere decent straps over bolts
    Drilling machine is always a bitch to transport
    Horizontal you need a special big enough pallet and blocks to keep...
  19. Yes .......................... Peter

    Yes ..........................

    Peter
  20. Remove the key and rotate the quill perhaps ?? ...

    Remove the key and rotate the quill perhaps ??

    Peter
  21. We put the 2 heaters in serie and tested again...

    We put the 2 heaters in serie and tested again After a much longer time as before it tripped once more
    So it did have some effect at least
    But.....
    After further inspection we discovered that it...
  22. Replies
    28
    Views
    1,894

    Buy buy buy buy

    Buy buy buy buy
  23. The thermal overload is in the 220volts 50 hz...

    The thermal overload is in the 220volts 50 hz supply line So that is where I measure
    Peter
  24. I measured less as 2 amps with a clamp on amp...

    I measured less as 2 amps with a clamp on amp meter Running at different speeds or starting had little to no influence
    Peter
  25. Replies
    28
    Views
    1,894

    It all depends on the price If it is GBP2500 or...

    It all depends on the price
    If it is GBP2500 or less

    BUY BUY BUY

    If under GBP 5000
    If it runs decent and all works sort of
    Buy

    Over GBP 5000
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4