Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rons

Page 1 of 60 1 2 3 4

Search: Search took 0.08 seconds; generated 46 minute(s) ago.

  1. Replies
    16
    Views
    547

    Welcome to your initiation.

    Welcome to your initiation.
  2. Replies
    12
    Views
    525

    OT: Buying from amazon.com ?

    If you missed the PBS Frontline program last Monday....

    YouTube

    Since I see people here buying stuff from amazon this may help you understand how they do business.
    I have avoided them for...
  3. Replies
    17
    Views
    1,080

    Ask customer support of any bearing manufacturer...

    Ask customer support of any bearing manufacturer for that particular size.

    If I was desperate I would get the dimensioned drawing for the bearing and calculate the volume of the toroid that houses...
  4. Replies
    145
    Views
    13,389

    My best watch is a Citizen Eco-drive. Hardly wear...

    My best watch is a Citizen Eco-drive. Hardly wear it.

    I like this independent watchmakers film:
    YouTube
  5. Amazing that stuff has lasted. It's pretty...

    Amazing that stuff has lasted.

    It's pretty simple to put everything back as it was. I would think about boring a hole in each end bell to fit a modern bearing.
  6. Replies
    5
    Views
    645

    My voltage display is "---" no matter what the...

    My voltage display is "---" no matter what the amperage knob is set to.
  7. Replies
    18
    Views
    980

    I have stripped paint off of metal and underneath...

    I have stripped paint off of metal and underneath is just brown rust. Rust from within. So it is important to clean the metal first.
    Whatever is the method I do a final wipe with some DuPont lacquer...
  8. Replies
    38
    Views
    1,667

    I stopped wearing clothes like a coat or apron....

    I stopped wearing clothes like a coat or apron. Loose ends, pockets that collect dirt and metal fragments, long sleeves, etc.
    The idea about the shield held with magnets is a good one.
  9. Replies
    18
    Views
    980

    If you are just using a rattle can then... Use...

    If you are just using a rattle can then...

    Use a spray gun with two part primers and paints. I use DuPont industrial coatings. It is used for painting metal that is outdoors like pipes, water...
  10. Replies
    38
    Views
    1,667

    Put up a cardboard barrier that is standing...

    Put up a cardboard barrier that is standing straight up with 2x4's. You can move it when the cutter changes direction. All the junk hits the board and not you.
  11. Replies
    38
    Views
    1,667

    Use a shield. In my keep clean moments I pick up...

    Use a shield. In my keep clean moments I pick up a rubber dust pan and hold it at a safe distance.
    I use clear Mylar sheets held by magnets behind my lathes.
    The chips from a manual mill will fly...
  12. Replies
    66
    Views
    3,092

    That would deny us of eminent domain. 278153

    That would deny us of eminent domain.

    278153
  13. The muscles can only do so much. The lens becomes...

    The muscles can only do so much. The lens becomes less liable with age. A lens replacement sounds scary to me.
  14. There are eye exercises that you can do. Somebody...

    There are eye exercises that you can do. Somebody I knew did them as assigned by a eye doctor. Some charts and glasses. Takes some time to see improvements.
    I'm not sure what you can figure out...
  15. Replies
    127
    Views
    7,534

    I've been in a few workspaces that have the...

    I've been in a few workspaces that have the ceilings two stories up and the heat is on all day. What a waste.

    The body parts that loose heat at the fastest rate are the ones with the tightest...
  16. Replies
    93
    Views
    4,246

    I used to ride with a few guys who always looked...

    I used to ride with a few guys who always looked at the profiles of their tires and always were trying to see how far the wear would grow.
  17. Replies
    13
    Views
    910

    A good cleaning with contact cleaner might bring...

    A good cleaning with contact cleaner might bring back the switch.
  18. That is probably what the manufacturer intended....

    That is probably what the manufacturer intended. Not sure but it sure would make hose hunting a lot easier.

    If that was my attachment I would shave down the rubber to whatever works or buy what...
  19. Replies
    13
    Views
    910

    How much did you charge for this info? :)

    How much did you charge for this info? :)
  20. Replies
    93
    Views
    4,246

    A work associate got into a accident on a popular...

    A work associate got into a accident on a popular route in the hills, everybody calls it Skyline. He had to be air-lifted to a hospital. He was back at work with a nice
    neck brace. It didn't take...
  21. Replies
    5
    Views
    645

    One maintenance item is the points adjustment...

    One maintenance item is the points adjustment underneath a cover in the back.
    A coolant flush is something that has to be done every 6 - 12 months. Otherwise the plumbing inside will rust out. It's...
  22. Replies
    7
    Views
    595

    Here, buy this stuff from Grainger. They need...

    Here, buy this stuff from Grainger. They need your dollars because their stock price is only about $315 per share.

    5 or more years ago the capacitors in the picture would have a GE label. Now they...
  23. Replies
    10
    Views
    695

    Check that your timer/relay is performing a...

    Check that your timer/relay is performing a one-shot operation correctly. If the chattering noise is coming from the small relay then
    it is not working correctly.

    You have a run capacitor array...
  24. One of the reasons I keep left overs is because...

    One of the reasons I keep left overs is because there is hope that the part can be salvaged and a piece of it can be made into smaller part(s) in the future.
    I opt for stainless types, brass,...
  25. Are they still in business? They were the last...

    Are they still in business? They were the last ones standing around here.
Results 1 to 25 of 1496
Page 1 of 60 1 2 3 4