Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Jim Christie

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds; generated 3 minute(s) ago.

  1. Another similar looking lathe turned up in a...

    Another similar looking lathe turned up in a Google Image search I did for Lathe Made in Poland
    How did resistance forces make barrels for Sten guns? - Quora
    Perhaps not an exact match for...
  2. Replies
    12
    Views
    586

    Very nice work. Here is a page about Ehrlich on...

    Very nice work.
    Here is a page about Ehrlich on Tony's site in case you haven't seen it before .
    Oscar Ehrlich Lathes
    There have been a few other Ehrlich lathes shown on this forum in the past ....
  3. Thread: AMT lathe

    by Jim Christie
    Replies
    7
    Views
    706

    While the lathe in this thread is larger than...

    While the lathe in this thread is larger than yours , the basics about thread dials and lead screw pitch are covered here that may give you some ideas ....
  4. Thread: AMT lathe

    by Jim Christie
    Replies
    7
    Views
    706

    You could probably adapt a used thread dial from...

    You could probably adapt a used thread dial from another lathe that has a lead screw of the same number of threads per inch and roughly the same diameter so that the gear at the bottom will fit....
  5. Your lathe has the tumbler reverse for the lead...

    Your lathe has the tumbler reverse for the lead screw on the inside of the head stock similar to a Seneca Falls lathe that makes it distinctive.
    There are a number of threads about lathes with this...
  6. There are a couple of pictures of a ship’s horse...

    There are a couple of pictures of a ship’s horse collar or horse shoe shoe thrust bearing mentioned by Joe Michaels at the bottom of post # 1 of this older thread....
  7. It isn’t from a grinder that I recognize. I...

    It isn’t from a grinder that I recognize.
    I know it isn’t one of the standard work heads from Cincinnati #2 , Brown and Sharpe 10N , Hembrug ,K.O. Lee or Tos ,that I know about
    Maybe some...
  8. Replies
    6
    Views
    2,663

    I’m not sure about this machine but on some...

    I’m not sure about this machine but on some drill presses and other small mills I have seen the front cone pulley fits on a short hollow tapered spindle that runs in a pair of ball bearings that...
  9. Replies
    9
    Views
    1,049

    I also wondered if it might be a British or...

    I also wondered if it might be a British or European Mill that started out with a different head and perhaps they made a deal with Bridgeport to buy the heads or someone adapted it later on .
    I...
  10. Here are some planer tool links that I may have...

    Here are some planer tool links that I may have posted in another thread before
    International Library of Technology: A Series of Textbooks for Persons Engaged in the ... : International Textbook...
  11. Replies
    38
    Views
    9,967

    Here is a link to another Lucas thread . Perhaps...

    Here is a link to another Lucas thread .
    Perhaps a different model than yours ....
  12. Replies
    10
    Views
    1,690

    Possibly made from a Lewis kit or plans ? Lewis...

    Possibly made from a Lewis kit or plans ?
    Lewis kit-built machine tools
    Lewis Machine Tool Co. - History | VintageMachinery.org
    I think there are some members of this forum who had or have one ....
  13. Replies
    7
    Views
    785

    I see Harold already posted the link to Tony’s...

    I see Harold already posted the link to Tony’s site.
    I think it predates 1980 but not sure .
    Omnitrade Machinery that used to be just off the south side of HWY 40 I think in Ville St.Laurent were...
  14. Replies
    28
    Views
    2,969

    I had seen a video on another aviation forum...

    I had seen a video on another aviation forum about Classic Wings who’s owner also owns Cord King ,a company building firewood processors shown in the early part of the video from 2011
    YouTube...
  15. Replies
    28
    Views
    2,969

    I was curious so I took a look at the video again...

    I was curious so I took a look at the video again and wondered if there might be 2 cylinders running the table on on either side of the trough in the centre of the bed
    It looks to me at this point...
  16. 90 |Year old Interlocking System in Toronto To Be Retired

    Union Station prepares to retire a vast interlocking system that's guided every train in and out of Toronto for almost 90 years.
    Someone sent me this link about the interlocking system at Toronto's...
  17. Replies
    28
    Views
    2,969

    A spiral planning setup similar to that mentioned...

    A spiral planning setup similar to that mentioned by Tyrone can be seen here
    International Library of Technology: A Series of Textbooks for Persons Engaged in the ... : International Textbook...
  18. H.W.Electric Repair posted about his Knight Mill...

    H.W.Electric Repair posted about his Knight Mill with and M-head in this thread....
  19. Replies
    72
    Views
    6,412

    The 10 B Lathes shown in the Model Engineer link...

    The 10 B Lathes shown in the Model Engineer link look very much like the lathes that were sold in Canada as the Inchametric 10 and the Enterprise 10 that were made in India.
    My father bought one in...
  20. Replies
    17
    Views
    1,678

    As has you noted the machine has been re purposed...

    As has you noted the machine has been re purposed for a special job .
    If it was for a vintage Boeing aircraft there maybe someone in one of the aviation groups that would eventually need the parts...
  21. Replies
    5
    Views
    833

    Maybe if you try a Google Image Search on...

    Maybe if you try a Google Image Search on Google.se for Something like Old Lathe made in Sweden but in Swedish, something that looks close may turn up.
    I tried this search
    Old Lathe Made in...
  22. Replies
    19
    Views
    3,952

    Here is a Link to a Blog post with more photos an...

    Here is a Link to a Blog post with more photos an information about the Canadian Car and Foundry Plant in Thunder Bay Ontario mentioned earlier that built not only the Hurricane but the Curtiss SBW...
  23. I also have a B&S # 45 . You can read what some...

    I also have a B&S # 45 .
    You can read what some of the other contributors posted about mine in this old thread ....
  24. John , You are probably right but often some of...

    John ,
    You are probably right but often some of those odd old things that are un recognized get tossed aside rather quickly only to find out later on that they actually were a missing part of the...
  25. The Tool post grinder mentioned by awander looks...

    The Tool post grinder mentioned by awander looks like a Dumore .
    They come in various sizes and when new came in a metal case with a number of accessories.
    I’m not sure what model that one is....
Results 1 to 25 of 1495
Page 1 of 60 1 2 3 4