Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Paolo_MD

Page 1 of 58 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    25
    Views
    933

    On the top of what Derek said, if the issue is...

    On the top of what Derek said, if the issue is simply/mostly tailstock alignment, if you cut a 6" piece between centers (i.e. driven by a dog, not chucked in the chuck), you should observe a...
  2. What you don't want to do on any lathe is to...

    What you don't want to do on any lathe is to engage the longitudinal feed and the half nuts at the same time, since it would try to run the carriage at two different speeds, and something will have...
  3. Replies
    4
    Views
    304

    Another beauty of conical bearings is the ease of...

    Another beauty of conical bearings is the ease of precise adjustment: although it's likely an overkill for the rear bearing (i.e. even if it is a little loose, it doesn't affect too much the...
  4. Yesterday I had the time to stop by and have a...

    Yesterday I had the time to stop by and have a chat with Gary at Cabin Fever. I managed to ask him a few things that, I thought, would be of interest to several people here.
    First, his primary...
  5. Replies
    12
    Views
    735

    Yes, Like in the picture that Joe attached to...

    Yes,
    Like in the picture that Joe attached to post #2, there was some gearing driving most likely a leadscrew, which was likely used both for threading and for longitudinal feeds.
    For what I can...
  6. Replies
    12
    Views
    735

    It looks like that lathe was born without back...

    It looks like that lathe was born without back gears. Maybe a pattern-maker lathe?

    Paolo
  7. Probably, the best would be for you to go through...

    Probably, the best would be for you to go through the following two publications:
    Hendey Machine Co. - Publication Reprints - Hendey Geared Head Lathe Bulletin 1246L-12-38 | VintageMachinery.org...
  8. On the top of the information (and instructions...

    On the top of the information (and instructions on how to distinguish a 12 speed from a 18 speed) provided to you in the other thread, what kind of information are you still looking for in order to...
  9. If you have enough room, you can put a large...

    If you have enough room, you can put a large enough open wrench between the drill chuck and the body of the tailstock and retract the quill till the back of the wrench is squeezed between the...
  10. Replies
    20
    Views
    2,155

    You might be approximately 1/3 of tooth off if...

    You might be approximately 1/3 of tooth off if two of the three jaws are swapped (and they could have been already swapped before you got it).
    Generally, anything round held by the jaws should be...
  11. The VN 38 is a completely different beast and I...

    The VN 38 is a completely different beast and I have serious doubts that the pinion and ring gear would fit (i.e. much larger cutter head, designed for much more power).

    Paolo
  12. Replies
    20
    Views
    2,155

    is the whole body of the chuck off center, or...

    is the whole body of the chuck off center, or only the "test bar" held by the jaws?
    If it's the second, are you sure that the jaws were re-inserted in the correct order/position?

    Paolo
  13. Replies
    4
    Views
    530

    I would suggest measuring the threads with the...

    I would suggest measuring the threads with the three wires method to see if it is indeed worn, or is tapered.

    Paolo
  14. Replies
    2
    Views
    718

    PM sent Paolo

    PM sent

    Paolo
  15. Replies
    33
    Views
    2,155

    I believe the thinnest it could be for B grade is...

    I believe the thinnest it could be for B grade is 6-8 in thick. The surface looks trashed and, to assess if it is somehow near to flat you need at least a trustworthy parallel, and tenth indicator...
  16. Replies
    6
    Views
    1,096

    The 22L has already limited headspace. By...

    The 22L has already limited headspace. By mounting the J head to the cutter head you'd end up with just a couple of inches between the table and the spindle.

    Paolo
  17. Thread: Hendey 14x8

    by Paolo_MD
    Replies
    24
    Views
    1,636

    According to EngineBill, the tin in the spindle...

    According to EngineBill, the tin in the spindle bearing crystallizes expanding (and locking) them. I have seen a similar effect on the bearings of a Barnes lathe belonging to a friend of mine. In his...
  18. Replies
    19
    Views
    1,232

    Another good point that can be taken from Brian's...

    Another good point that can be taken from Brian's pictures is that, cutting upside-down an internal keyway is equivalent to locking the clapper box without having to do so physically.
    Given that the...
  19. Replies
    14
    Views
    1,417

    I'm afraid you are confusing flatness with...

    I'm afraid you are confusing flatness with alignment, or you haven't described well what you're doing. A few pictures would also help us understanding better.

    The blue will transfer to the areas...
  20. The problem is with the software handling the...

    The problem is with the software handling the pictures on this forum not recognizing the orientation information now in the metadata of most every picture. Modern image editing software recognize...
  21. Bill, just a couple of quick comments. On MSDS...

    Bill,
    just a couple of quick comments.
    On MSDS sheets you do not find all the ingredients (chemicals known to be "inert" can be omitted) and you get at most a range of percentage in the whole mix,...
  22. Yes and no

    True, mixing doesn't reduce the size of the particles.
    However, size matters also for something else: larger particles tend to drop out of solution significantly faster. There is where mixing...
  23. I have also experienced some separation and...

    I have also experienced some separation and granularity in a couple of bottles of Canode.
    Richard's advice of "power-mixing" it is a very good one.
    I did some relatively successful experimentation...
  24. If you suspect there is congealed oil in the...

    If you suspect there is congealed oil in the spindle bearings, I'd suggest filling (and keep filling) the oilers with kerosene (which is a very light lubricant) and turn the spindle by hand from time...
  25. I'm not familiar with the specific machine. A...

    I'm not familiar with the specific machine.
    A couple of years ago I've helped moving a Micromaster 618 and I estimated the weight in the neighborhood of 3000-3500 lb

    I suspect yours is a bit...
Results 1 to 25 of 1449
Page 1 of 58 1 2 3 4