Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: triumph406

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    26
    Views
    1,460

    Here's a link to a manual Ikegai A-20 Manual...

    Here's a link to a manual

    Ikegai A-20 Manual with Electricals | store.lathes.co.uk
  2. Replies
    340
    Views
    10,537

    That's insane, the virus transmission is viral...

    That's insane, the virus transmission is viral load x exposure time. So 3 people in a van, closed doors, if one of them has the virus, even if asymptomatic, what are the chances of the other two...
  3. Replies
    340
    Views
    10,537

    I'm sure they do. The 'Made in China' label is...

    I'm sure they do.

    The 'Made in China' label is right next to the valve for blowing up their female companion.
  4. Replies
    340
    Views
    10,537

    'Crystal clear' drunk people can't socially...

    'Crystal clear' drunk people can't socially distance, say police in England | World news | The Guardian
  5. Replies
    340
    Views
    10,537

    I suspect he's so far gone he thinks AON, Epoch...

    I suspect he's so far gone he thinks AON, Epoch Times and Breitbart are fake and libtard news now.
  6. Replies
    340
    Views
    10,537

    Your really stupid if you think this a good move....

    Your really stupid if you think this a good move. Even the dipshit guvnors in AZ and TX have shut the bars.

    Send me your address so I can send you a BLM t-shirt.
  7. Replies
    340
    Views
    10,537

    Another of Fauci's concerns is the US will never...

    Another of Fauci's concerns is the US will never reach herd immunity because the anti-vaxxers will refuse a covid vaccine, and there's enough of them to make a tangible difference for the rest of...
  8. Replies
    1,305
    Views
    120,499

    No I'm pulling for my friends, I don't care for...

    No I'm pulling for my friends, I don't care for Boeing much, but I'd like to see my friends working again
  9. Replies
    1,305
    Views
    120,499

    Well let's hope their sucessfull in getting...

    Well let's hope their sucessfull in getting re-certified, I know multiple people in a few PNW machine shops who were very badly effected by the 737MAX debacle, and then covid.
  10. Somewhere the OP mentioned he's 60. Haven't...

    Somewhere the OP mentioned he's 60.

    Haven't been able to figure out his problem yet, he's just generally obnoxiuos
  11. Replies
    101
    Views
    4,669

    When the OP finally get's his **** together and...

    When the OP finally get's his **** together and decides to get a real Fadal (or Mori,Okuma,Hass etc)

    This is a good read

    Speedie's Fadal reality checklist (pre 2014)
  12. Replies
    101
    Views
    4,669

    A review from a Bulgarian web site. ...

    A review from a Bulgarian web site.

    Предпочитам да залепя чужди предмети в задника си, отколкото да купя друга от тези машини. Бившата ми жена е по-надеждна от онзи син на курва машина. тя със...
  13. Replies
    101
    Views
    4,669

    This was posted on a Taiwanese site of the people...

    This was posted on a Taiwanese site of the people who made that machine under what looked like to be the specicifications tab
    ...
  14. Replies
    101
    Views
    4,669

    Well ok then.

    Well ok then.
  15. Replies
    101
    Views
    4,669

    I was trying to find where I read the 3016L was...

    I was trying to find where I read the 3016L was the best Fadal they made

    I couldn't find the thread but I realized they were talking about the boxway 3016, so it couldn't have been the 3016L
  16. Replies
    101
    Views
    4,669

    If you do look at a rebuild, you have to check if...

    If you do look at a rebuild, you have to check if it's an AC or DC machine.

    DC machines I think went up to '94, AC after that. So a rebuilt DC machine would be an old machine, not a big deal if...
  17. Replies
    101
    Views
    4,669

    Obv can't make your mind for you, but It would be...

    Obv can't make your mind for you, but It would be a Fadal for me.

    I've never seen that Hurco control before, so no idea what the learning curve would be. You could be up and running and making $'s...
  18. Do you have trouble typing when your wearing that...

    Do you have trouble typing when your wearing that white pointy hood?
  19. Replies
    19
    Views
    1,348

    Likely it is rpseguin

    Likely it is rpseguin
  20. Confucius might have had the same reaction that...

    Confucius might have had the same reaction that Eric Clapton, Jeff Beck, Pete Townsend had when they first saw Jimi Hendrix use an instrument in a way they hadn't thought possible (yet)
  21. Thread: Recession?

    by triumph406
    Replies
    2,971
    Views
    154,740

    You need to come up with a new insult, this ones...

    You need to come up with a new insult, this ones getting old.
  22. Have you checked in the current climate how easy...

    Have you checked in the current climate how easy it is to get a loan for a new property? I assume you've already checked otherwise you wouldn't be discussing this now.

    Good luck
  23. I ran a side business out of a 2 car apartement...

    I ran a side business out of a 2 car apartement garage in Huntington Beach for years.

    I would get material in the mornings on the way to my regular job in the morning, or Saturday mornings.
    ...
  24. Replies
    101
    Views
    4,669

    Probably a great machine, until you need to...

    Probably a great machine, until you need to either buy parts or get a Hurco tech to come out and look at it.

    Where are you in CA?
  25. Replies
    101
    Views
    4,669

    Make sure you look at Fadals with the extended Z...

    Make sure you look at Fadals with the extended Z travel. Standard Z travel machines are next to worthless imho. Especuially if you get a 4th, or a 4th/5th axis rotary. Plus if you were have to...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4