Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: mhajicek

Page 1 of 41 1 2 3 4

Search: Search took 0.01 seconds.

  1. I picked up one of these about a year ago:...

    I picked up one of these about a year ago:
    https://www.mscdirect.com/product/details/00919522?rItem=00919522

    It's serving me well cutting 17-4 H900 and Ti6Al4V. The 1" blade lasts a lot longer...
  2. Replies
    31
    Views
    1,376

    I have two parts in an assembly with this...

    I have two parts in an assembly with this situation. Part "A" has a deep drilled bore with a step smaller at the bottom, likely to be drilled from the other end. Part "B" is a stepped shaft that...
  3. Replies
    13
    Views
    770

    First thing I'd check is the thrust bearings.

    First thing I'd check is the thrust bearings.
  4. Replies
    29
    Views
    5,166

    mdi #500 = 0

    mdi #500 = 0
  5. Replies
    7
    Views
    888

    This is what I do. No stock prep for aluminum or...

    This is what I do. No stock prep for aluminum or plastic, cut a 60° dovetail for titanium or pre-hard steel. Quick swaps on center between the vise and collet fixtures.
  6. I run 1000PSI TSC through the collet while...

    I run 1000PSI TSC through the collet while cutting so it stays clean. I blow it out a bit and give it a spin by hand between tools.
  7. Replies
    17
    Views
    1,202

    Try one of these: 271144

    Try one of these:

    271144
  8. I have a few DNA-11's for 1/8" shank tools. They...

    I have a few DNA-11's for 1/8" shank tools. They work pretty well. I don't remove the collet from the nut.
  9. Replies
    11
    Views
    812

    Not if you don't tell them what it is. Usually...

    Not if you don't tell them what it is. Usually people post an actual problem or question, with a descriptive subject line.
  10. Replies
    89
    Views
    5,902

    My thinking is it's a Yamaha R6, (or R1 with dual...

    My thinking is it's a Yamaha R6, (or R1 with dual contact), not an F-350. It's a lot faster and it corners real nice, but if you're moving sacks of concrete take the truck.
  11. Replies
    4
    Views
    468

    I'm using Hangsterfers S787D in Ti with good...

    I'm using Hangsterfers S787D in Ti with good results. Never gets stinky.
  12. Replies
    32
    Views
    1,748

    Digitals are the easiest to read. Also the...

    Digitals are the easiest to read. Also the easiest to mis-read when you don't notice it's zeroed wrong or that it skipped a bit due to coolant. I find I get the best readings from dials, until...
  13. Replies
    9
    Views
    1,303

    It's like an F-35. Trying to do too many things...

    It's like an F-35. Trying to do too many things at once, no good at any of it.
  14. Replies
    126
    Views
    7,381

    H11 IS a tolerance. Your scenario was throw a...

    H11 IS a tolerance. Your scenario was throw a part at a guy and ask him to make it without a print, and you ridiculed the concept that they had the gall to ask for a print. Yeah, if you bring in a...
  15. Replies
    126
    Views
    7,381

    If you hand me a part and ask if I can make it I...

    If you hand me a part and ask if I can make it I will ask for a fully dimensioned and toleranced print (or a model that includes tolerances on every dimension) before giving an answer. If you don't...
  16. Replies
    9
    Views
    1,303

    What do you want to do with it? I've never seen...

    What do you want to do with it? I've never seen anyone happy with a lathe/mill combo.
  17. Load monitoring can be your friend.

    Load monitoring can be your friend.
  18. Thread: Tool Holders

    by mhajicek
    Replies
    20
    Views
    1,904

    Got a lot of Maritool holders here, ER-11, ER-16,...

    Got a lot of Maritool holders here, ER-11, ER-16, ER-32, and a couple endmill holders. Coolant thru studs in all. Can't find a fault with them. I've also got their induction machine, which is...
  19. Replies
    22
    Views
    1,580

    That's a hobby machine, and as such is against...

    That's a hobby machine, and as such is against the rules to discuss here. That said, either use a flycutter or take multiple passes with a much smaller solid carbide cutter.
  20. Replies
    28
    Views
    1,591

    A 3" indexable is probably too big to run on a...

    A 3" indexable is probably too big to run on a VF-2 in 4140 prehard with good results unless it's a shallow finish pass. You have a Yamaha R-6, not a Ford F-350. I'd use a smaller solid carbide...
  21. Send me the machine and I'll make money with it....

    Send me the machine and I'll make money with it. :)
  22. Better rigidity is always better, all else being...

    Better rigidity is always better, all else being equal. It also tends to be more expensive. Is it worth paying for, for your parts in your shop? That's up to you. It can also have some...
  23. Replies
    13
    Views
    1,588

    I run 15K for hours on end in Titanium for...

    I run 15K for hours on end in Titanium for finishing small surface details with a 1/32" ball. I'm getting a quote for a Toodle so I can run it faster.
  24. Replies
    38
    Views
    2,856

    I just did that a couple weeks ago on a VMC with...

    I just did that a couple weeks ago on a VMC with trunnion to make a fixture mounting plate, but with a much finer stepover. It ensures that a circle at any given radius on the machined surface will...
  25. Okay, here's your helpful answer. It's a bad...

    Okay, here's your helpful answer. It's a bad idea, and you could have had the right stuff delivered by now if you had ordered it when asking your question. Some people spend a lot of time and...
Results 1 to 25 of 1007
Page 1 of 41 1 2 3 4