Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: GENERALDISARRAY

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Are these 6044 drives? is there not a 4xx alarm?...

    Are these 6044 drives?
    is there not a 4xx alarm?

    There is both a trimmer overload level as well as an actual circuit breaker on those drives.
    you will need the maintenance or motor/drive book to...
  2. We have two of those Beere tip shears here....

    We have two of those Beere tip shears here. Subspindle lathes means they get used infrequently nowadays.
  3. Replies
    5
    Views
    714

    I thought green screen was something the...

    I thought green screen was something the weatherman used.

    Maybe thats where the vector-graphing comes in.
  4. Replies
    17
    Views
    796

    The Acramatic PC2100. Is this an episode of ...

    The Acramatic PC2100. Is this an episode of "where are they now"?

    spoiler alert; the scrapyard

    Meanwhile the OP observes radio silence.
  5. Replies
    5
    Views
    512

    dc motor could be a tach type setup or a...

    dc motor could be a tach type setup or a pulsecoder only. I cant speak on the tach type. But the encoder type is fairly straight forward As and Bs and Marker pulses with power and ground.
    I know...
  6. My fix for the roundy rounds, I spent no time...

    My fix for the roundy rounds, I spent no time trying to fix the encoder and went ham on the de-miniaturized replacement.

    268383

    268382
  7. Replies
    32
    Views
    3,632

    the number for the pre-celos parts list is...

    the number for the pre-celos parts list is PL-NLX2500Y-A02 if that helps. It is kind of abridged, it only 85 pages and half of that is accessories.
  8. Replies
    16
    Views
    1,815

    His Granny is gonna slit his bag for ruining her...

    His Granny is gonna slit his bag for ruining her fancy tablecloth.
  9. Replies
    62
    Views
    4,325

    500 sounds reasonable to me. You might tempt down...

    500 sounds reasonable to me. You might tempt down him with cash. And I dont think you will be less than that DIY, if that is even a possibility, some auctions require liability insurance for rigging....
  10. Wish it was closer,the last machine rescue road...

    Wish it was closer,the last machine rescue road trip nearly kilt me.
  11. Replies
    16
    Views
    1,186

    Unless that is a very new machine,and something...

    Unless that is a very new machine,and something has changed. Most lathes do not "rigid" tap with the lathe spindles. If you want to rigid tap on-center you will have to use an axial driven tool.
    ...
  12. Replies
    16
    Views
    1,186

    On-center tapping with the lathe spindles? Or...

    On-center tapping with the lathe spindles? Or driven tool tapping?
  13. Replies
    24
    Views
    1,517

    How handy On machines that will not handle a...

    How handy

    On machines that will not handle a null toolchange, I put a block delete in front of the Tx and M6 lines. That way during setup or program restarts there is an easy way to avoid an...
  14. Replies
    2
    Views
    465

    Can you please elaborate? I know on the mapps...

    Can you please elaborate?
    I know on the mapps machines, you had to change at least one parameter on a new machine to allow turning with Y off zero.
    In mapps, there was a parameter to allow...
  15. Australia has trees?

    Australia has trees?
  16. I think it says in the manual "the barfeed...

    I think it says in the manual
    "the barfeed signal is internally decoded, but external drivers are not supplied for it"
  17. OP you have mail

    OP you have mail
  18. The easiest way would be a timer relay inline...

    The easiest way would be a timer relay inline with the coil circuit of the chip conveyor contactor.

    To have it use a software timer during concurrent program execution would require it to be in...
  19. Replies
    4
    Views
    718

    Two cast parts located in fixture for secondary...

    Two cast parts located in fixture for secondary operations, no X,Y probing. But you get the idea.
    #501 and #502 are called with G68 at each operation for respective part.

    Weirdo Z values are...
  20. If I am understanding. Is the issue that you dont...

    If I am understanding. Is the issue that you dont have an accurate way to measure the TSC of the tapers?

    High Quality Precision Dimensional Inspection Gages

    model 77M with ball styli look on...
  21. Does it do this with a program resident in...

    Does it do this with a program resident in memory? Or only while DNC?
  22. Replies
    16
    Views
    7,040

    Let us know how that ends up. In Borat voice;...

    Let us know how that ends up.

    In Borat voice; You will never get this





    This would have been better with the spoiler tags, buy I couldn't get them to work.
  23. Replies
    32
    Views
    2,630

    mill a square hole? This sounds like a job for...

    mill a square hole? This sounds like a job for the Bridgeport.
  24. Replies
    6
    Views
    807

    We have a 17" Clausing Turn-nado. bought new...

    We have a 17" Clausing Turn-nado. bought new around 86. Not that old in my book. And Clausing still sells parts for this machine.

    I would investigate why it needs new spindle bearings before...
  25. I think there is a Kondia Supermill underneath.

    I think there is a Kondia Supermill underneath.
Results 1 to 25 of 95
Page 1 of 4 1 2 3 4