Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Dan from Oakland

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Are you certain that the pinion teeth are badly...

    Are you certain that the pinion teeth are badly worn? I'm about 97.5% certain that your 10 tooth pinion is cut on an enlarged blank due to the low number of teeth. Even a 20 degree PA 10 tooth gear...
  2. It may be a DIN5482 17 X 14 Spline. The module...

    It may be a DIN5482 17 X 14 Spline. The module for that is 1.6
  3. Replies
    17
    Views
    1,363

    what diameter are "C"? look like Morse taper...

    what diameter are "C"? look like Morse taper counterbores- what size pilot hole?
    thx
  4. How hard is the part? tapping or single point...

    How hard is the part? tapping or single point threading? Carbide tap? Why? Roughing the thread prior to HT might be a good idea, but that bore is going to shrink with heat treating, but its better...
  5. This works on stubborn and almost stripped head...

    This works on stubborn and almost stripped head socket head cap screws very well- so. Take a VERY big brass hammer and pound the small end of the shank toward the boring head. The idea is to...
  6. It's pretty hard to beat the motion of a two tool...

    It's pretty hard to beat the motion of a two tool Gleason bevel gear generator as it rolls out the involute on each gear tooth, retracts, indexes and feeds back into depth, all the while rolling the...
  7. Replies
    7
    Views
    670

    My experience has been that unless you have gobs...

    My experience has been that unless you have gobs of chips- like hundreds and hundreds of #, no one wants them. Don't know how big your trailer is but. . . .
  8. Appears to be a nice lathe in great shape for its...

    Appears to be a nice lathe in great shape for its age, but as others have said or implied, you will be fortunate to probably get half your current asking price.
    The widget on the back side of the...
  9. Do you know how to check communication settings...

    Do you know how to check communication settings at the control? If you are not familiar with setting up RS232, the sending computer settings need to match the receiving computer settings. I'm like...
  10. Tip the head left to right- cutter spindle does...

    Tip the head left to right- cutter spindle does not have to be parallel to table. Plenty of other issues to deal with though.
  11. Replies
    10
    Views
    389

    Yup- 30 tool carousel was an option versus the 20...

    Yup- 30 tool carousel was an option versus the 20 tool version.
  12. Replies
    10
    Views
    389

    What Control- Yasnac or Fanuc?

    What Control- Yasnac or Fanuc?
  13. Replies
    3
    Views
    533

    1st thing I would do is clean the contacts in the...

    1st thing I would do is clean the contacts in the auxiliary contact block that latches the coil/control circuit. There should be a wiring diagram in the cover of the contactor enclosure.
  14. Nothing worse than a lift with forks that are too...

    Nothing worse than a lift with forks that are too short. To me, 36" forks are too short unless your work area is so tight that nothing else will work. 48" forks are pretty useful for most tasks, but...
  15. So 4mm axial pitch has a lead of .1575". A 20 DP...

    So 4mm axial pitch has a lead of .1575". A 20 DP spur gear has a circular pitch of Pi/20= .1517" or 3.85mm The addendum of a 20 dp gear is 1/20=.050"=1.27mm.

    You want a gear OD of 20mm, so the...
  16. You really don't need a gundrill to drill thru...

    You really don't need a gundrill to drill thru 16". That's only 8" from each end. A good quality aircraft drill will easily drill that deep. Just saying.
  17. Replies
    6
    Views
    585

    When we got bumped to $200 for a few small shafts...

    When we got bumped to $200 for a few small shafts less than a few pounds and they tacked on an additional $50 charge for "certs" that we did not request, I said so long as well. Found another local...
  18. Inspect it well- don't get one with creases or...

    Inspect it well- don't get one with creases or dents on the top that will hold water and eventually start to rust thru. Paying a little more up front is worth it. Rememeber they have been around...
  19. Replies
    29
    Views
    25,848

    Which worm gear- the one under the drive motor?

    Which worm gear- the one under the drive motor?
  20. What happens when you 1) press the button 2) hold...

    What happens when you 1) press the button 2) hold the tool holder up in the spindle and 3)take your finger off the button?
  21. Replies
    11
    Views
    854

    Actually there are two stub possibilities- AGMA...

    Actually there are two stub possibilities- AGMA Stub or Fellows Stub. The 16DP Fellows stub as I recall is 16/21 not 16/20.
  22. I would offer you $200 for one of each size. ...

    I would offer you $200 for one of each size. thanks. dmcgearsatyahoo.com
  23. Replies
    17
    Views
    1,571

    It was only the 17" Sheldons that were also...

    It was only the 17" Sheldons that were also offered as NC and then CNC machines. The 17" is a pretty stout machine. I have a CNC version if anyone need a running project.
  24. Replies
    8
    Views
    835

    Here is the remains of the Futaba DRO's I had at...

    Here is the remains of the Futaba DRO's I had at one time.

    298603
  25. Douglas- you are fortunate- I have one for my SL2...

    Douglas- you are fortunate- I have one for my SL2 12 Station machine but I have to borrow one from my neighbor for my 10 station SL3. Like everything else, they get lost or tossed.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4