Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JCByrd24

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Yes you can.

    Yes you can.
  2. Replies
    26
    Views
    1,397

    This is an Internet forum not some sort of...

    This is an Internet forum not some sort of accredited institution. A forum is only as good as its members. There should be no presumption of respect or that any long standing member is correct (same...
  3. Replies
    26
    Views
    1,397

    Post number 2 wasn’t exactly welcoming and it...

    Post number 2 wasn’t exactly welcoming and it didn’t improve much from there...just keep your mouth shut if you’re not going to help a guy out when he’s clearly somewhat new. A post last week asking...
  4. Replies
    26
    Views
    1,397

    Just because no one else has mentioned it IMHO...

    Just because no one else has mentioned it IMHO that lathe is overpriced, at least from what I can see in the pics. Looks like it’s covered in surface rust which means not only is it a project to...
  5. With MT4 and 5HP you can do better than 1”...

    With MT4 and 5HP you can do better than 1” starter and associated boring bar I’d guess, but like has been said I don’t think spade vs twist matters much unless you can run carbide spade with your...
  6. Replies
    508
    Views
    34,593

    Because in this application there is almost no...

    Because in this application there is almost no difference in strength. Pull studs are in pure tension until things are going wrong and in pure tension they’re the same strength and one has more room...
  7. Agree with these guys. I work in government...

    Agree with these guys. I work in government oversight of defense contractors, we often review our contractors quality records and their subcontractors, we don't give them sheets to fill out, we just...
  8. Replies
    24
    Views
    1,390

    Concur with gustafson. Fine pitch blade, and slow...

    Concur with gustafson. Fine pitch blade, and slow on the feed and this is an easy job. The issue is work holding and a different saw is unlikely to improve that, especially a slower one. Make up some...
  9. Replies
    9
    Views
    925

    I'm guessing he'd get a second VFD so he can have...

    I'm guessing he'd get a second VFD so he can have independent controls for each machine. You can get a decent VFD for the mill for $100 on amazon (Lapond has good support and manuals). Your proposed...
  10. Replies
    137
    Views
    9,424

    cdcotools has import wedge CXA starter package...

    cdcotools has import wedge CXA starter package for $213. Not bad and plenty good enough for a home shop guy. Or it's not too hard to make a little spacer block to raise up a BXA a little bit and save...
  11. Replies
    8
    Views
    823

    Concur with John, the best you will get new for...

    Concur with John, the best you will get new for $1500 to 2K is a benchtop Chinese mill. Those scaled down BPs are around $4k. The OPs mill will easily get 1500-2K in New England. Those 3/4 scale BP...
  12. Replies
    18
    Views
    1,498

    He's pulling your leg because your machine is...

    He's pulling your leg because your machine is borderline against the rules here, trust me you don't want him to elaborate.
  13. Replies
    26
    Views
    2,301

    I heard just recently some evidence that limiting...

    I heard just recently some evidence that limiting spindles at say 90% of full speed added to their life significantly. But if the 12k and 15k are the same mechanically you are already doing that, and...
  14. Replies
    18
    Views
    1,498

    The bearing preload as well as the seals will...

    The bearing preload as well as the seals will cause drag. It should still be smooth rolling, not crunchy or anything, but it may drag. Many manufactures specify the preload be set by adjusting the...
  15. A swag here but yes I think you'd be fine with...

    A swag here but yes I think you'd be fine with your plan (I had a portion of my driveway blacktopped a couple of years ago so I have a little experience in the area, and a friend of mine parks his...
  16. Replies
    8
    Views
    664

    You won't find many drills significantly larger...

    You won't find many drills significantly larger that 3/4" in MT2 because the taper will not drive them without spinning. I have seen up to 1" though. General rule is not to drive something much...
  17. Replies
    16
    Views
    1,682

    For spills I do immediate cleanup with brake...

    For spills I do immediate cleanup with brake parts cleaner and shop towels. Will pull even old stains out of concrete, no expense/cleanup of speedidry and quicker.

    For a persistent slow leak under...
  18. Replies
    7
    Views
    698

    Agreed. Rusty and non-powered to me is about...

    Agreed. Rusty and non-powered to me is about worth little more than scrap value. He's just dreaming waiting for a buyer without a clue.
  19. 1) Off all the badness that could happen I do not...

    1) Off all the badness that could happen I do not think a crash would warp the saddle.

    2) Yes the saddle should sit down under its own weight and no you should not use the rear gib to pull it...
  20. Dude, as Bill mentions the back gauge as you call...

    Dude, as Bill mentions the back gauge as you call it should be straight across. It's incredibly unlucky that you've come across three saws with the same issue, which is clearly a design/manufacturing...
  21. Replies
    140
    Views
    9,827

    I think the issue is the machine abuse of a very...

    I think the issue is the machine abuse of a very expensive machine. Would you test mud or snow tires on a brand new Corvette.....no. You know the saying "he's hard on equipment". Some of us who don't...
  22. Replies
    36
    Views
    1,984

    I just had a 9K high efficiency Fujitsu unit...

    I just had a 9K high efficiency Fujitsu unit installed in my house, for heating and cooling. It was great this summer for cooling and has been so far for heating as well, though we've only hit...
  23. Replies
    14
    Views
    1,691

    My alma mater! BTW we add steel on for breaking...

    My alma mater! BTW we add steel on for breaking the bottle on steel ships too.
  24. Larry’s got it, left hand drill. Stud should be...

    Larry’s got it, left hand drill. Stud should be relatively loose it’s not like it’s corroded in there. Left hand drill will often walk it right out. I start small and then jump up in size to...
  25. Just want to get some folks thoughts on this...my...

    Just want to get some folks thoughts on this...my own lathe has rubber/plastic wipers that are pretty ineffective and I want to replace some time. I know felt has been used traditionally but I'd...
Results 1 to 25 of 177
Page 1 of 8 1 2 3 4