Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hoss710

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. I could be wrong, ( its been some time since I...

    I could be wrong, ( its been some time since I have played with the newer controllers) but thought there was either a setting or parameter to allow up to 500 tool offsets.
  2. Replies
    49
    Views
    3,181

    did you compare the software number to thev1...

    did you compare the software number to thev1 written in the back of the cabinet? I could be wrong, but that may have had a software upgrade. if so some of the other parameters values will change....
  3. Replies
    49
    Views
    3,181

    tou should see it during boot up mode. or under...

    tou should see it during boot up mode. or under diagnostics, then page down a few pages.
  4. Replies
    49
    Views
    3,181

    it of curiosity. what software is in the machine?

    it of curiosity. what software is in the machine?
  5. Replies
    49
    Views
    3,181

    are you sure you don't have a gearbox? and are...

    are you sure you don't have a gearbox? and are you certain about the delta/ wye. I had a similar problem once . and it was from someone who had a gearbox had disabled it in low gear and told the...
  6. Replies
    49
    Views
    3,181

    on parameter 57 disable g.b should be a 1 like...

    on parameter 57 disable g.b should be a 1 like you have. I'd leave the invert gearbox alone as once you disable it I cant see how it comes into play ? I guess you could try that 1 either way. but on...
  7. Replies
    49
    Views
    3,181

    if it has delta / wye then the parameters need to...

    if it has delta / wye then the parameters need to reflect that. if so disable g.b. should be a 0 . delta/wye should be a 1
  8. the older haas controls stop at N100000 . just...

    the older haas controls stop at N100000 . just remove your N 's and it should run fine.
  9. my 75 hp runs on a 100 amp breaker. but has a...

    my 75 hp runs on a 100 amp breaker. but has a soft start , so I have never tripped the breaker . I have been running it that way since December 2005. Just make sure you have the air supply you need...
  10. Replies
    25
    Views
    6,626

    the SS uses a 30 hp motor ( unless you ordered it...

    the SS uses a 30 hp motor ( unless you ordered it with a option 40) the standard vf2 is only a 20 hp spindle motor.
  11. I have a customer that runs a vf2ss on a 50 hp...

    I have a customer that runs a vf2ss on a 50 hp American rotary. but its has been border line if the air compressor comes on during a rom ramp up . or a rapid move, I have seen the machine fault out....
  12. Replies
    25
    Views
    6,626

    I have a vf2SS running off of a phase converter. ...

    I have a vf2SS running off of a phase converter. I'm using a 100 amp breaker for both the converter and machine. also running 2/0 wire.
  13. Replies
    8
    Views
    1,442

    are you talking about that banging noise? I dont...

    are you talking about that banging noise? I dont hear anything else?
  14. I used Kluber Isoflex NBU 15 . its expensive. ...

    I used Kluber Isoflex NBU 15 . its expensive. but it's what I had in hand when I had rebuilt a few Chiron spindles. you might very well find a substitute that costs a lot less.
  15. ok to answer your questions. Haas will say no...

    ok to answer your questions. Haas will say no dont grease it. but the truth is I have greased mine . and happy I did. I rebuilt the gearbox on my 96 vf3 about a year ago. while I had everything...
  16. Replies
    34
    Views
    2,758

    from memory yes I remember it being recessed.

    from memory yes I remember it being recessed.
  17. Replies
    34
    Views
    2,758

    yes they basically do bolt a out of the create...

    yes they basically do bolt a out of the create hrt310 to the frame of the machine. the rotary table should have oil in it , and shouldn't have grease. the draw bar that clamps the tombstone to it...
  18. Replies
    34
    Views
    2,758

    the rotary table has a rather large brake...

    the rotary table has a rather large brake internally. you need air to the solenoid, and for the solenoid to activate to supply air to release the brake. do not attempt to move rotate table without...
  19. have you tried contacting Haas applications in CA...

    have you tried contacting Haas applications in CA ? they are normally very good at walking you thru issues like this.
  20. Replies
    6
    Views
    443

    I have a kt 21Kia with the yasnac control. other...

    I have a kt 21Kia with the yasnac control. other than 1 quirky problem I had ( seemed like no 1 could figure it out, but I was able to and all good after that) it's been a amazing little machine. ...
  21. Thread: Haas vf-o

    by Hoss710
    Replies
    8
    Views
    642

    not a video ( although haas has a series of...

    not a video ( although haas has a series of videos that go over some of the basics) the haas manual to me is 2nd to none on walking you through all of your G, M codes. check it out ! It lays it all...
  22. Replies
    88
    Views
    5,669

    unfortunately between programming, fixturing,...

    unfortunately between programming, fixturing, tooling, coolant, machine payments, electricity, and labor. $60.00 a hr doesn't cover it all. now if you had 4 or 5 machines running at the same time,...
  23. Replies
    88
    Views
    5,669

    And this is the reason many shop owners either A)...

    And this is the reason many shop owners either A) work a full time day job somewhere else. or B) can't or don't make it.
    C) get lucky and stumble into a great customer/ contract .
    I'm sure there...
  24. Replies
    34
    Views
    2,758

    I should have mentioned it was on the back side....

    I should have mentioned it was on the back side. but it looks like you found it :-) . that regulator could very well go to the table clamp. unfortunately someone has messed and changed some things....
  25. just noticed a dark spot around the R3 markings....

    just noticed a dark spot around the R3 markings. might want to give that a closer look to. all the current for tool changer in and out. as well as turret rotation go through the 2 groups of the...
Results 1 to 25 of 220
Page 1 of 9 1 2 3 4