Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Lazyman

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    29
    Views
    5,639

    The mistaway in my shop definitely helps get the...

    The mistaway in my shop definitely helps get the fog out but the place still stinks of coolant. I also wonder how much the hepa would help.
  2. Replies
    26
    Views
    7,971

    Damn, there goes my plans for lights out...

    Damn, there goes my plans for lights out machining. What a huge liability.
  3. Replies
    49
    Views
    6,978

    I don't always have to align it up as I do as...

    I don't always have to align it up as I do as Eric mentioned and pull it toward me as a torque it down. However, I still end up having to check it it anyways with an indicator to make sure and...
  4. Replies
    49
    Views
    6,978

    Just to add my experience for future readers. I...

    Just to add my experience for future readers. I have 2 earlier Gen 4 20" orange dual stations with the durabar jaw carriers.

    The good things are the clamping feedback is very good and the vise...
  5. Replies
    12
    Views
    1,522

    I personally would find having to close the doors...

    I personally would find having to close the doors to run the auger super annoying but I have thought to myself that what If I lost my balance or something while shoveling the chips toward the auger...
  6. Replies
    14
    Views
    2,908

    This is the first time I heard of anyone paying...

    This is the first time I heard of anyone paying for installation on a Haas. Mine was completely free including leveling and probe installation. The price also seems ridiculous.
  7. Replies
    60
    Views
    16,517

    I get the feeling lots of guys here will have no...

    I get the feeling lots of guys here will have no idea about the podcast. Titan appears to be an actual brand ambassador for synergy as his pictures were all over it at IMTS Blaser booth. I recently...
  8. Replies
    22
    Views
    2,251

    This happening to be on a Saturday too. It was...

    This happening to be on a Saturday too. It was annoying because the machine was paid in full as far as they are concerned. It was one time and then that's it. It would have been nice to be told that...
  9. Thanks, I ordered a fluke volt meter to replace...

    Thanks, I ordered a fluke volt meter to replace the junk one I was using to make sure it's not the meter and see the readings I get.
  10. I have checked the connections and nothing is...

    I have checked the connections and nothing is loose. I noticed on the other hobby forum there is a thread with the exact same machine and also a lathe that both have LED lights flickering. Could it...
  11. The lights operate 110-240VAC but the outlet...

    The lights operate 110-240VAC but the outlet tested was 120V. No flicker at all. The lights are powered via a power distribution board in the electrical panel in the machine. The machine is powered...
  12. Phase perfect phase converter and LED lights flickering in machine?

    Hi, I have a 355 20hp phase perfect wired up to a haas VF-2SSYT. The LED worklights in the machine flicker slightly when the machine is idle. It was always a very slight flicker before that never...
  13. Replies
    60
    Views
    16,517

    Mneuro, can you tell us your process to make sure...

    Mneuro, can you tell us your process to make sure it was absolutely clean?
  14. I got a VF-2SSYT in a garage with dedicated...

    I got a VF-2SSYT in a garage with dedicated 150amp service and perfect phase and my lights flicker every time the spindle ramps up after tool change. If the 5hp compressor fires up at the same time...
  15. Replies
    23
    Views
    2,319

    I was going to say the same thing. 10hp ATC...

    I was going to say the same thing. 10hp ATC router spindles are more expensive than a Haas spindle for example.

    To the OP. You might as well just call the manufacture to be because it did say over...
  16. Replies
    60
    Views
    16,517

    Thanks for the reply. The price at $200 seems...

    Thanks for the reply. The price at $200 seems reasonable if it truly performs. It's in the same range as Qualichem extremecut 250c. The performance of Qualichem was not an issue for me, but I did...
  17. Replies
    60
    Views
    16,517

    New clear Blaser Synergy 735 coolant?

    Has anyone tried the new Synergy coolant? I'm considering switching from Qualichem to this stuff as I'm looking for stuff that has less odor and less issues on the skin. Being clear like water would...
  18. Replies
    133
    Views
    23,487

    Implex, I don't disagree, and just to clarify. I...

    Implex, I don't disagree, and just to clarify. I don't use Fusion 360 for CAD at all with the exception of doing small modifications to parts. I only use the CAM portion and that's the only thing I...
  19. Replies
    133
    Views
    23,487

    I really don't worry about trusting Autodesk when...

    I really don't worry about trusting Autodesk when the competition is charging 10x plus what they are charging for not enough more value for the work I do. I'm just not worried about them suddenly...
  20. Replies
    133
    Views
    23,487

    I guess it can described like home "ownership."...

    I guess it can described like home "ownership." Even after you pay off the mortgage, the state can come take your house away if you miss your property tax payments. Subscription is like renting...
  21. Replies
    133
    Views
    23,487

    Some of the responses crack me up. People are so...

    Some of the responses crack me up. People are so concerned about Autodesk holding them for ransom. Its funny because they have recently taken away the ultimate version and now offer only one version...
  22. For those, who wanted to know what I did. I...

    For those, who wanted to know what I did. I ordered a set of Meyer Gage Z class pins in .001" increments from amazon. They worked well and worth the investment as I have been using them to check lots...
  23. Replies
    33
    Views
    3,633

    Just wanted to add, that I could see the "wave"...

    Just wanted to add, that I could see the "wave" as the forklift drove over my driveway. My drive way was already in bad condition though and the small damage it did do didn't bother me. The machine...
  24. Replies
    29
    Views
    5,639

    I was at IMTS and saw Haas had a new centrifugal...

    I was at IMTS and saw Haas had a new centrifugal mist collecting system outfitted on their machines. It had a long piping around the machine to return coolant back to inside the machine. It appeared...
  25. Replies
    33
    Views
    3,633

    Here are pics of my delivery on VF-2SSYT 2017...

    Here are pics of my delivery on VF-2SSYT 2017 model. The YT is about 7 inches wider than standard machine machine. In my case with 24Tside mount tool changer was actually about the same height as the...
Results 1 to 25 of 65
Page 1 of 3 1 2 3