Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Ianagos

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. You can cold start the machine with the z lower...

    You can cold start the machine with the z lower than it should be. But then the axis stop will not be set correctly and you can easily over travel. But it will allow you to do everything you want and...
  2. Replies
    22
    Views
    1,753

    I think youíll be fine if you just clean all the...

    I think youíll be fine if you just clean all the rust out with some cleaner and a brass brush or bristle brush. They are just like added oil retention pockets.
  3. As far as a good post I believe Autodesk has one...

    As far as a good post I believe Autodesk has one listed but if you need I have a proven one I use for my fadals.
  4. Replies
    10
    Views
    640

    I didnít see it listed but it requires: 2 ac...

    I didnít see it listed but it requires:
    2 ac bearings 7304b 20x52x15
    3 seals skf 12360
    1 seal skf 11138
    And a 7/8 preload shim between .001-.002

    The bearings I usually see in there are nsk...
  5. Replies
    0
    Views
    185

    Fadal probing macros

    So I have very little experience with macro programming but I now own 4 fadals and Iím looking to instal a probing system on my newer machine a 2001 4020. As of right now I donít have anything setup...
  6. Replies
    19
    Views
    1,785

    Mine was being very noisy and not tracking well...

    Mine was being very noisy and not tracking well even when perfectly setup. What I ended up doing was setting the tension relatively light and then using a soap bar to put a little dry soap on the...
  7. Replies
    49
    Views
    12,064

    Iíll have to try that when I get back home. I...

    Iíll have to try that when I get back home. I guess I started doing it a certain way and just stuck to it because it worked.

    Now itís nice to be able to set the tools offline but it definitely...
  8. Replies
    49
    Views
    12,064

    A Fadal toolsetting system that doesn't suck!

    Wow I just saw this and it looks like you did a really good job on this but there is a much easier way to set offsets in the fadal. And it lets you use the standard tool setting utilities for the...
  9. Replies
    17
    Views
    2,521

    Got something a bit larger but Iím not asking too...

    Got something a bit larger but Iím not asking too much. 14x48 (I think) American pacemaker 1973. https://uploads.tapatalk-cdn.com/20190807/2af7be86a7c0a9a44557d374ed1406d7.jpg
  10. I agree with the yg1 being more susceptible to...

    I agree with the yg1 being more susceptible to the corner coming off but they leave better surface finishes for me. Iím glad you guys got your own website you guys do make great tools just not as...
  11. Cutting threads on a howa? I think you could get...

    Cutting threads on a howa? I think you could get away with using a die. Now if you did that to my barrel that I paid you to install Iíd want my money back and take my barrel out of your hands as fast...
  12. Replies
    6
    Views
    1,283

    I offered you 14k a few months ago. Bought I...

    I offered you 14k a few months ago.
    Bought I ended up with a Fadal 5020Aht in nicer shape.

    Iím interested in a good deal on a 4020 or 4525 maybe even a 6030 with Datc and chip conveyer though. I...
  13. Replies
    37
    Views
    4,033

    I got a quote from szgh too do you have any...

    I got a quote from szgh too do you have any experience with them? Iím interested.

    Seems like a good control to retrofit a machine with.
  14. Replies
    5
    Views
    950

    Interested you have pictures?

    Interested you have pictures?
  15. Replies
    193
    Views
    28,708

    From what I was told the 250c and 251c are almost...

    From what I was told the 250c and 251c are almost the same just 251c wasnít allow for aerospace stuff and it is better for stainless. Donít quote me but i think it has chlorine additives.
  16. Replies
    193
    Views
    28,708

    I run 251c at 7-8% and itís not bad worked ok...

    I run 251c at 7-8% and itís not bad worked ok even form tapping 316 stainless. But I mostly use it in alluminum.
  17. Looking to buy a 4 jaw chuck close to Atlanta Ga

    I have a 10Ē toolmex 4jaw and a cheaper 10Ē but Iím not sure but I think they are both integrates d16.

    Edit: the toolmex chuck is plain back 10Ē semi steel 4 jaw brand new. Dunno place of...
  18. I couldnít imagine it would be easy to make...

    I couldnít imagine it would be easy to make affordable and good way covers for such a complex design like the one above.


    For the op something that I think gets missed a lot on these small...
  19. Replies
    23
    Views
    3,717

    Man Iíd be driving up to pick that up right now...

    Man Iíd be driving up to pick that up right now if it were not so far away. How do you find these great deals. :sarcasm:
  20. I wish the 1Ēx6Ē was necked back. Anybody know of...

    I wish the 1Ēx6Ē was necked back. Anybody know of someone who could neck it back and the cost?
  21. I have a -4 cpu and possibly memory expansion if...

    I have a -4 cpu and possibly memory expansion if you want to go that route send me a pm.
  22. Replies
    14
    Views
    1,192

    The vfd is not a phase converter Iím amazed the...

    The vfd is not a phase converter Iím amazed the thing worked at all but makes sense that the control wonít turn on.
  23. You can buy a 1400-5c processor but it may also...

    You can buy a 1400-5c processor but it may also mean you need to change your other cards aswell. The -2 system is older and while it can still do 3d machining itís not very fast aswell as it has very...
  24. Replies
    193
    Views
    28,708

    Iíve been running it with tap water no problems....

    Iíve been running it with tap water no problems. Compared to other stuff Iíve seen this is the best hands down.
  25. Replies
    2
    Views
    423

    Deublin Rotary Union PN 355-000-002

    PMs are full
Results 1 to 25 of 469
Page 1 of 19 1 2 3 4