Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: enginebill

Page 1 of 48 1 2 3 4

Search: Search took 0.02 seconds.

  1. It is a number 24 vertical mill and will have a...

    It is a number 24 vertical mill and will have a #10 Brown & Sharpe taper spindle. It is cheap but it is too far gone as far as I am concerned. Too many missing original parts and too much damage.
  2. Yes, you can remove the caps and spindle and the...

    Yes, you can remove the caps and spindle and the lathe will be fine although it is much more convenient to stitch the belt than to remove the spindle to get the belt on.
  3. Replies
    34
    Views
    3,828

    It is a Crossley H. I was working on it for a...

    It is a Crossley H. I was working on it for a customer and I was experimenting with hot tube lengths and I was using the countershaft of the lathe for starting of the engine.
  4. It looks like someone might have bored it out for...

    It looks like someone might have bored it out for a collet.
  5. Post some clear photos, there is probably...

    Post some clear photos, there is probably something in the bore now.
  6. Yes, no room for that weight on my lathe. It has...

    Yes, no room for that weight on my lathe. It has been a while since I looked at my lathe and I thought it was gibbed but when you said yours was weighted, I second guessed myself. The lathe in your...
  7. Joe, I could use some pictures of the carriage...

    Joe, I could use some pictures of the carriage weight also how it hangs on the carriage. Mine does not have one and with the crossmembers in the center of the bed, I didn't think it used one.
  8. Replies
    2
    Views
    366

    Here is some info. Van Norman Machine Tool Co. -...

    Here is some info. Van Norman Machine Tool Co. - History | VintageMachinery.org
  9. Replies
    8
    Views
    962

    You can probably get a stock gear and...

    You can probably get a stock gear and modify/combine it with what you have.
  10. Joe, the tailstock spindle of my lathe is only...

    Joe, the tailstock spindle of my lathe is only stamped with a 7, no date.
  11. That looks to be the same as my Lathe & Morse....

    That looks to be the same as my Lathe & Morse. Mine is an 18" swing with 3MT centers. The top of my tailstock is stamped with a 66 and a 7.
  12. You can safely braze the crack. It is an...

    You can safely braze the crack. It is an unconstrained crack and it will not crack again.
  13. Replies
    4
    Views
    584

    If you send measurements and the missing numbers,...

    If you send measurements and the missing numbers, Rob Gill can make you a new tag, [email protected] . Expect to pay around $150 for the tag.
  14. Can you post a video of the operation? It doesn't...

    Can you post a video of the operation? It doesn't look like the belt wants to move at all. The countershaft belt on my Putnam planer is only about 4' from the line shaft and those tight and loose...
  15. John, That is a nice looking planer. The belt...

    John, That is a nice looking planer. The belt shifter needs to be on the leading side belt. In your photo the belt should be running down, the belt should be good and tight too. And obviously the...
  16. Replies
    9
    Views
    1,133

    I have a 16 pole 3 phase motor with a 435 full...

    I have a 16 pole 3 phase motor with a 435 full load rpm but it is only 3/4 HP, it is the size of a modern 10 HP motor though.
  17. Replies
    2
    Views
    461

    It sounds like this is your first lathe. The...

    It sounds like this is your first lathe. The spindle inside diameter at the chuck end is tapered for a dead center and is probably 4, 4 1/2 or 5 Morse taper. You say it turns something out of round,...
  18. Replies
    24
    Views
    30,942

    Sticky: The last I heard was that some stuff was scrapped...

    The last I heard was that some stuff was scrapped by the person that Chad sold the building to. Also the city is working towards taking the whole property over.
  19. Replies
    71
    Views
    6,313

    Dave, I think there would be three hubs on the...

    Dave, I think there would be three hubs on the wheel shaft. The two hubs on the left are the inside and outside of the outside hubs, two per wheel. The hubs on the right are the inside and outside of...
  20. Replies
    30
    Views
    2,329

    Couldn't you use an impulse from another magneto?

    Couldn't you use an impulse from another magneto?
  21. Here is a web site where you can sell the gas...

    Here is a web site where you can sell the gas engines, Medium Flywheel Engines and Parts For Sale
    Here is one for steam engines, Steam and Traction Engines For Sale
    The machinery can be sold...
  22. Replies
    71
    Views
    6,313

    What I see there is a copper bowl since the...

    What I see there is a copper bowl since the boiler is copper the copper circle would have to be bowl shaped for the pressure. The strap is on the bottom, the copper bowl is just above the strap and...
  23. Replies
    71
    Views
    6,313

    Send me your email address in a private message...

    Send me your email address in a private message by clicking on my name and I will forward it to him.
  24. Replies
    71
    Views
    6,313

    Have you talked to Alex Karnes? He is a young kid...

    Have you talked to Alex Karnes? He is a young kid but is very knowledgeable about steam.
  25. Replies
    71
    Views
    6,313

    You will figure it out eventually.

    You will figure it out eventually.
Results 1 to 25 of 1190
Page 1 of 48 1 2 3 4