Search:

The resin level caused the false contact. Thanks to both of you for your answers.

I am having a Contact Alarm problem with my FX 10. When i try to center position I get a contact alarm when it is not touching any thing. I even get the alarm with out a part in the machine. I have...

I was hoping that some one had a generic video or manual for robots. It seems imposible to just get every thing going from the 3 manuals that i have. The robot is a LR Mate 100i that is like new. I...

Does any one know of a training video or cd available for a Fanuc robot? It appears to be very difficult to learn from the factory Fanuc manuals. Thanks

Thanks for all the information. Is there any place that i can obtain a Kryoflux floppy in the usa?

Have any of you intergrated any of these with a Fanuc control. It seems that all i see are Haas controls. Is it possible to do without a mega buck installation? Thanks

No such luck as having another floppy drive. What are my options as to replace it? Thanks

Some one in the shop shut off the power to our Mits FX 10. I discovered no power today when i came to use it. I got nothing on the screen when i powered it up. So I attempted to reload the files as i...

Has any one used a tool setter arm to check for tool breakage in a lathe program? Fanuc 18 control, Daewoo lathe. We would like to avoid the expense of a Renishaw if we can. Thanks

I am having trouble getting on the accuratereloading web site. it will not allow me to send him an email. I don't have his phone # either
Hope some one can be of help.

How can i contact Les Brooks to purchase his plans? i have contacted the accuratereloading.com web site and no one knows what i am talking about.

Do the Haas HA5C rotaries have a home sensor or do they rely on the encoder?
Thanks
Pete

I am looking for a source that can supply an engine rebuild kit for our H40XMS forklift with a Mazda M4-2.0G engine. Any one have any ideas? Thanks

I recently purchased a Haas HA5C rotary 4th axis with a Haas S5C controller box. When we first turn it on we get a (A Hot) alarm after pressing cycle start it then locks up and has to be restarted to...

I just obtained a Haas 7" Black box rotary table and controller that is not working properly. I can power up the table and jog it in both directions a short distance then it alarms out. I removed the...

After letters from our attorney Haas sent us an agreement to buy back the machine for 85% of purchase price dated 10/05/16. We did not receive it until 10/14/16. I forwarded the agreement to our...

The problems continue. Thru spindle coolant quit yesterday. it was only about 3 months old. replaced the old one.
try and keep every one aware of whats going on

Thanks for the advise every one. There is a chart as mentioned above found in the system,G data, D0000 thru D0009,enter tool numbers there. Running fine now.

Got it fixed Thanks to you all

I wish it was that simple. it does not change tools, thinks that pot already has a tool in it.

I screwed up big time and crashed z axis on my Sharp SV2414. Z axis was off by about 1/2". Simple to fix right. I set parameter write to 1 and went to parameter 1815 bit 4 and changed X to zero...

I have a Sharp sv2412 and I have gotten the tool numbers and pot numbers screwed up. How can I set the control so that Tool 1 goes to pot 1, tool 2 to pot2 and so on?

Makrep,

Thank you for the help. We have ordered a new PD21B.

Makrep,




Sorry have been out of town. tried the disk drive thing again with no luck. Checked the voltage at terminals H & N with 105 volts across them. 88 volts at H to ground and 23 volts at...

I tried that but the floppy drive will not come on.

I think that it must be a power issue between the main power switch and control, I just don't know what to check