Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Ohio Mike

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    8
    Views
    596

    Definitely not a Bridgeport. Does have a...

    Definitely not a Bridgeport. Does have a Cincinnati look about it. Could be European?
  2. Replies
    6
    Views
    442

    Again distance is an issue but I think H&W will...

    Again distance is an issue but I think H&W will take your machine on trade for one already refreshed. From a financial perspective its going to cost between $7500-8500 to do a BP which puts in you...
  3. What drill do you have and what parts do you...

    What drill do you have and what parts do you need? A lot of helpful people here.
  4. One issue is the internet service being used. For...

    One issue is the internet service being used. For the vast majority the upload speed is a fraction of the download speed. For example Charter/Spectrum's flagship package is 100Mbps download but that...
  5. Replies
    20
    Views
    824

    Weight should be around 16500 lbs.

    Weight should be around 16500 lbs.
  6. Its for a work stop, not sure Aloris sell those...

    Its for a work stop, not sure Aloris sell those anymore. Google "Aloris Guide Stop"
  7. When I ordered my complete 33 piece set of...

    When I ordered my complete 33 piece set of Triumph Twist Drill S&D bits they each came in a plastic sleeve along with a Huot rack for them.
  8. Replies
    4
    Views
    444

    If no one he comes up with one call H&W Machine...

    If no one he comes up with one call H&W Machine in Ft Wayne IN. If anyone has M head parts machines its probably them. They can sell you the hand wheel but I would hold out for one on eBay if one...
  9. Replies
    27
    Views
    1,681

    I'd use CRC's "Lectra-Motive" Electric Parts...

    I'd use CRC's "Lectra-Motive" Electric Parts Cleaner.
  10. Replies
    29
    Views
    1,989

    Try this....

    Try this.
    http://vintagemachinery.org/pubs/2102/17983.pdf
  11. Replies
    29
    Views
    1,989

    The LeBlonde you are thinking of would be a Regal...

    The LeBlonde you are thinking of would be a Regal which is a lighter duty machine. This would be a 12 inch 'NB' Heavy Duty Engine Lathe. Produced from 1950 to 1957 this one is a 1956.
  12. My Monarch 12CK has the original start/stop...

    My Monarch 12CK has the original start/stop Westinghouse controls (in fact Westinghouse was the original owner) but the lathe also has a lever operated drum switch at the rear of the machine which...
  13. Replies
    9
    Views
    868

    Used on a horizontal milling machine. The "crane"...

    Used on a horizontal milling machine. The "crane" allows you to remove an accessory head and "park" it on the machine.

    269897
  14. Replies
    32
    Views
    3,667

    Actually the 2HL was 40 taper and the earliest 2H...

    Actually the 2HL was 40 taper and the earliest 2H were apparently 40 also. Another early 2H feature was the lack of the overarm pinion to push the rams in and out. However by July 1940 the...
  15. Thread: Oliver 300HD

    by Ohio Mike
    Replies
    4
    Views
    680

    I have not run one but the biggest difference...

    I have not run one but the biggest difference with the ACE is that instead of moving the work piece into the wheel (like a traditional surface grinder) you traverse the cutting head into the work...
  16. What are the chances set number one went to...

    What are the chances set number one went to someone with a YouTube or Instagram presence. When some of these guys post about a new tool you can watch the eBay prices jump.
  17. Replies
    9
    Views
    777

    The early machines had cast base (like a bell...

    The early machines had cast base (like a bell with a door in it), later machines were on pipe cabinets. If a machine differs it was probably transplanted due to damage or other requirements. As...
  18. Replies
    10
    Views
    933

    ^^^ This ^^^

    ^^^ This ^^^
  19. Replies
    25
    Views
    2,034

    About testing oil flow... Running the machine...

    About testing oil flow... Running the machine with the head stock open will create an world class oil spill in an instant. Even in low gear that input shaft is turning its normal 800+ RPM. The way I...
  20. Replies
    25
    Views
    2,034

    Its my understanding the 12CK could be purchased...

    Its my understanding the 12CK could be purchased with spindle speeds up to 1000 RPM. I wouldn't be too worried with running one that fast by playing with the motor pulley. Mine is setup for 800 RPM...
  21. The stock motors were 1 HP 1750 RPM. They were...

    The stock motors were 1 HP 1750 RPM. They were designed to have a lower counter shaft speed of 300 RPM. Great drills. Mine had back gear issues. I replaced mine with a stock gears from...
  22. Replies
    19
    Views
    1,419

    I never ever recommend a novice use skates. I...

    I never ever recommend a novice use skates. I wouldn't ever think of using them on something that top heavy.
  23. The short answer because people keep buying them.

    The short answer because people keep buying them.
  24. Replies
    19
    Views
    1,419

    +1 I think $250-750 is the likely sale price...

    +1

    I think $250-750 is the likely sale price in the iron rich rust belt. At an industrial plant auction it would bring scrap at a weekend farm/estate auction more towards the top.
  25. Replies
    14
    Views
    1,378

    I found a 62" King listed as weighing 65,000. A ...

    I found a 62" King listed as weighing 65,000. A Morey in the 96" range weighs 95,000.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4