Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: agieman

Page 1 of 13 1 2 3 4

Search: Search took 0.02 seconds.

  1. Guys to my knowledge this machine is still...

    Guys to my knowledge this machine is still supported by GF. Applications and service phone support is still free.
    1.800.282.1336 x-1947 for APPS x-1960 service.
  2. Replies
    11
    Views
    522

    PM Me. i have what you need

    PM Me. i have what you need
  3. Replies
    6
    Views
    555

    Where are you in Switzerland? I think you need a...

    Where are you in Switzerland? I think you need a service call I can be on the next plane lol
    This can be a few things. do you get air bubbles during erosion?
  4. Replies
    6
    Views
    555

    the screw head being pointed to in the pic sets...

    the screw head being pointed to in the pic sets the tension for the "pizza cutter" at the end of the green arm. (250grams). The black wheel that the "pizza cutter" is resting on with green hub and 4...
  5. For the record, AgieCharmilles phone support is...

    For the record, AgieCharmilles phone support is still free. Most machines are still supported but not all. There are still some old timers willing to talk about the really old machines but you have...
  6. Replies
    6
    Views
    555

    i am going to assume you mean a 420 message. the...

    i am going to assume you mean a 420 message. the following info is if that is the situation. Most likely the wire is slipping. thread the wire AND with the handbox ON run the belts. grab the black...
  7. Replies
    11
    Views
    522

    i will try and locate parameters for you. do you...

    i will try and locate parameters for you. do you have the tec tables?
  8. Replies
    11
    Views
    522

    do you have ST25 if so us that.

    do you have ST25 if so us that.
  9. Replies
    3
    Views
    404

    it is set up for serial input. you can use...

    it is set up for serial input. you can use hyperterminal in windows. a web search shows it is available for windows 10. most older versions of windows contain hyperterminal in accessories. you will...
  10. Not a sensor malfunction more of a design issue....

    Not a sensor malfunction more of a design issue. keep wire on it and you should be fine. thank you for the kind words.
  11. Replies
    8
    Views
    2,076

    Welcome back my friend!

    Welcome back my friend!
  12. Replies
    11
    Views
    1,314

    when I ran Wire machines regularly,I ran a grease...

    when I ran Wire machines regularly,I ran a grease distribution program on Monday mornings just to keep everything lubed up. I had a habit of setting parts up in the same general area and mostly used...
  13. leo, take look at the position of RX1 it is the...

    leo, take look at the position of RX1 it is the pulley above the wire spool that controls the wire spool motor. you dont want to power up the machine with the pulley all the way up. roll the wire...
  14. Replies
    12
    Views
    1,833

    Hi Jay, GF has another machine to remove grown...

    Hi Jay, GF has another machine to remove grown parts from a build plate, the CUT AM500. It's designed from the ground up to serve the additive machining industry. it cuts horizontally, uses wire...
  15. Replies
    2
    Views
    658

    FYI: pressure sensors on charmilles288249 were...

    FYI: pressure sensors on charmilles288249 were used much earlier than the introduction of this machine.that being said this machine does not have a set up like that. most likely the float switch...
  16. Replies
    12
    Views
    1,833

    there was a progress 4 kicking around on Ebay...

    there was a progress 4 kicking around on Ebay with a 28in.Z. it was in Ohio somewhere. might be worth a google search it was short money as i recall.
  17. yes to the encoder cards IMC-06/09 if both have...

    yes to the encoder cards IMC-06/09 if both have three sections. i think it is the DMD for XY that is missing the third section. the DMD's are interchangable but you have to swap the PMO's that are...
  18. the excellence has 2 measuring systems on x and...

    the excellence has 2 measuring systems on x and y.
    system 1 rotary encoder on motor
    system 2 glass scale. check connections between glass scale and IMC board.
  19. Replies
    11
    Views
    2,807

    are you using the same tec file for the different...

    are you using the same tec file for the different thicknesses? are you sure its tec for 1.5 in thick material?
  20. Replies
    14
    Views
    1,424

    Check the PH of the water. It sounds like you...

    Check the PH of the water. It sounds like you have some type of chemical reaction going on.
  21. Replies
    7
    Views
    1,126

    has anyone from service visited the machine or...

    has anyone from service visited the machine or was this diagnosed by phone?
  22. Replies
    22
    Views
    2,657

    As a guy who has fixed hundreds of those Agie...

    As a guy who has fixed hundreds of those Agie machines, i usually planned on 2 full days to redo geometry and that was if i didn't have to work on the Z axis. When it was right it was amazing what...
  23. Replies
    4
    Views
    984

    just my two cents. i have yet to see the agie...

    just my two cents. i have yet to see the agie that cant be fixed. software is hard coded on eproms not any hard drive tec is not on machine and has to be entered manually from a chart. parts are...
  24. does it thread automatically?

    does it thread automatically?
  25. Replies
    7
    Views
    1,423

    here is another vote for hermann Schmidt!

    here is another vote for hermann Schmidt!
Results 1 to 25 of 304
Page 1 of 13 1 2 3 4