Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: moonlight machine

Page 1 of 60 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    10
    Views
    1,850

    I have a few NSK items I find them absolutely...

    I have a few NSK items I find them absolutely average.
  2. Send that toy down the road and get a real mill.

    Send that toy down the road and get a real mill.
  3. I know of a few scrap yards that could handle...

    I know of a few scrap yards that could handle that job with no problem.
  4. Replies
    11
    Views
    702

    Where is the lip around the edge? Stuff will be...

    Where is the lip around the edge? Stuff will be falling off that one!
  5. Did you drill through to measure the wall...

    Did you drill through to measure the wall thickness? Is the material thickness stamped on the plate? Photo please. Did you have it ultrasonically tested? Post the results please. Post the length,...
  6. Replies
    13
    Views
    2,247

    I wonder if there is an adaptor or back plate to...

    I wonder if there is an adaptor or back plate to fit that chuck to put it on a L1 spindle?
  7. It is easy to lower a tailstock, just pull the...

    It is easy to lower a tailstock, just pull the tailstock off its base and have at it with your mill. That said it would be good to know for sure it is .050 high. Very unusual for a tailstock to wear...
  8. Air France is parking all their A380s as well....

    Air France is parking all their A380s as well. Only in use for 10 years, they are going to take a beating on that deal.
  9. It will not make a mess if it is full of water....

    It will not make a mess if it is full of water. The first tiny crack will relieve all the pressure and you will lose about an ounce of water. Water will not compress, the only pressure is in your...
  10. Sensible engineer.....Now there's an oxymoron!!!

    Sensible engineer.....Now there's an oxymoron!!!
  11. I would imagine you were called in to do the post...

    I would imagine you were called in to do the post mortem on both those compressors and tanks..... You have no way of knowing the safety valve was damaged and the tank was over pressure. My...
  12. That's important, when it blows up and kills...

    That's important, when it blows up and kills somebody it needs to be the "correct" color. Clean it all you want, epoxy coat the inside, whatever. If you use it without a hydro test you are nuts.
  13. So the f'in MORON goes right out and buys another...

    So the f'in MORON goes right out and buys another P O S compressor. The IDIOT is proud of it as well.
  14. Only way to know for sure is a hydrotest. Fill...

    Only way to know for sure is a hydrotest. Fill it with water and pressure test it.
  15. I suppose you think there lots of engines with...

    I suppose you think there lots of engines with .093 diameter valve stems? Good luck with that! I have an ER collet on my valve grinder that would do it but it is the only one I have ever seen.
  16. Replies
    31
    Views
    1,751

    If there was a shortage of aluminum for cans you...

    If there was a shortage of aluminum for cans you would think scrap cans would be worth more. I called around last week, .18 to .30 / lb. A year ago .65 / lb.
  17. Replies
    9
    Views
    705

    I have an old Magnescale that with one bad scale...

    I have an old Magnescale that with one bad scale that I'll sell for 200.00
  18. Nice job but it seems like a lot of work for...

    Nice job but it seems like a lot of work for something you can buy from msc for $13.85 each.
  19. I give it a week, the carolina will be on...

    I give it a week, the carolina will be on craigslist
  20. Why not? If it does not work you can still do it...

    Why not? If it does not work you can still do it the way I did it afterword.
  21. Blame California, They taxed movie and TV...

    Blame California, They taxed movie and TV production right out of the state. Remember you morons who think taxing the shit out of the rich will solve everything, they are rich, they can afford to...
  22. No Idea what the current price for a Centroid...

    No Idea what the current price for a Centroid control is. When I did mine I bought the best one they had with all the bells and whistles and most of the options as well. I had lots of work for it and...
  23. I had lots of trouble with the axis drive motors,...

    I had lots of trouble with the axis drive motors, they had an encoder built in for which no parts were available to John Q Public. The only place that would work on them was in Chicago. They would...
  24. Looks like a V2xt with a Boss control. Generally...

    Looks like a V2xt with a Boss control. Generally speaking the control is so unreliable that the iron is in great shape. There is only one place in the states that will work on the axis drive motors...
  25. [QUOTE=Bluechipx;3575080]I've been told that when...

    [QUOTE=Bluechipx;3575080]I've been told that when logical mental reasoning and physics clash, go with physics, so here is my dilemma. When I built my home I wanted a large aquarium, 1,000 gallon or...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4