Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Tryhard

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    816

    Just keep it away from the dust the best you can....

    Just keep it away from the dust the best you can. Will wreak havoc on your check valves in your oil lines.
    I have an Onsrud 3 axis machine near my Haas VF also. Only cut aluminum and plastic parts...
  2. Your code is confusing, are yadda commands not...

    Your code is confusing, are yadda commands not case sensitive?
    :willy_nilly:
  3. Replies
    25
    Views
    3,842

    My machine had dark, dark stains on the way...

    My machine had dark, dark stains on the way covers and the paint. Dark like black coffee.
    I could buff them, sand them or scotchbrite disc them off, but they would not clean off or even smear using...
  4. Replies
    13
    Views
    2,338

    Love hearing stories like this. CountryGuy and...

    Love hearing stories like this. CountryGuy and Hoss710 are absolutely lifesavers. Couple others here are good too.
    But these two guys have been hands-down the best part of clicking on this site....
  5. WOW THAT'S IMPRESSIVE!!! Or maybe it would be,...

    WOW THAT'S IMPRESSIVE!!!
    Or maybe it would be, but I am just not as thrown off by your point of view. Simply tools of your trade.
    My point of view is that of a hobbyist/entrepreneur. Should be no...
  6. Replies
    2
    Views
    835

    I understand your want and excitement. Try...

    I understand your want and excitement. Try looking in your parameters for TC ENABLE or whatever and see if you can enable it. Then try your entries again. Not sure if your machine would have the...
  7. How do you guys not understand that the new (and...

    How do you guys not understand that the new (and in some cases free) software as of the last several years have added such things as adaptive tool paths, visualization, part arrays and cut&paste tool...
  8. You guys are confusing yourselves. The original...

    You guys are confusing yourselves. The original poster was struggling with the program. I commented on my post processor not knowing the center of an array. Sure the button rant was semi off topic,...
  9. Did the working motor work on other drives? Is...

    Did the working motor work on other drives?
    Is problem following axis wire harness?
  10. I recall this being discussed recently in THIS...

    I recall this being discussed recently in THIS THREAD HERE.
    Hope it helps.
  11. Replies
    2
    Views
    882

    I think they are the same as the $15 ones that...

    I think they are the same as the $15 ones that ebay offers arent they? Believe thats whats on my machine.
  12. Thank you. You are absolutely correct and that is...

    Thank you. You are absolutely correct and that is useful information for the original poster. But I wasn't the OP.
    My problem was I was thinking out loud with my comments related to modifying the...
  13. Why even bother to raise your blood pressure by...

    Why even bother to raise your blood pressure by clicking on thread titles which you make clear are beneath your golden input?
  14. I use Inventor HSM (same cam) and was pleasantly...

    I use Inventor HSM (same cam) and was pleasantly surprised to see this added in the program. However if you have an array of parts in multiple vises or a fixture it will still center table for part...
  15. Thank you Turbo442 for the very detailed and...

    Thank you Turbo442 for the very detailed and complete response!
  16. Replies
    25
    Views
    14,993

    Looking to do this on a 98 Haas also. Have macros...

    Looking to do this on a 98 Haas also. Have macros and scale/rotation turned on too.
    Could you share your wiring diagram for the probe/tool setter ?
  17. Ended up going with the Eastwood QST 30-60. ...

    Ended up going with the Eastwood QST 30-60.

    Overall quality is a bit better than I'd expected and the unit is very quiet. It takes about 3mins to fill from empty and maybe 30 seconds or so to fill...
  18. Replies
    9
    Views
    1,617

    My setting #36 was turned OFF. Turned it on and...

    My setting #36 was turned OFF.
    Turned it on and worked just fine. Afterward, I also tried same thing with it turned off. Didn't think it would let me, but it started up. I cancelled it out quickly...
  19. Is anyone actually running the Mobil 1 5w20...

    Is anyone actually running the Mobil 1 5w20 synthetic oil for this?
    Seems kinda thin, but appears to be the Haas approved substitute for the Mobil 625.
  20. Replies
    29
    Views
    3,140

    I'd think you could fit anything thru a 12x12...

    I'd think you could fit anything thru a 12x12 door. Just go here and look at the shipping dimensions.
  21. Replies
    13
    Views
    1,672

    Qucik fix to a Haas coolant pump going out.

    Just to close out this thread, Kustomizer had it right, this was the problem. Oddly enough, and as unlikely as it sounds, the problem was the same with BOTH pumps.


    For anyone finding themselves...
  22. Replies
    29
    Views
    3,140

    Your biggest hurdle on the VF3 and larger...

    Your biggest hurdle on the VF3 and larger machines are gonna be getting it thru the door and operating height. (YouTube: "Lucas Is Busy" he put a VF3 in by himself in a very unconventional way)...
  23. Replies
    29
    Views
    3,140

    Know a guy running a VF3 on a 15hp rpc. I'm...

    Know a guy running a VF3 on a 15hp rpc. I'm running a 20hp Haas and 10hp onsrud on a 25hp rpc. Several others on here also running multiple machines simultaneously on a single rpc.
    And I recall...
  24. Replies
    29
    Views
    3,140

    Hoss, What are you doing with all of those...

    Hoss, What are you doing with all of those machines? You jobshopping?
  25. Think maybe it had something to do with the oil...

    Think maybe it had something to do with the oil breaking down the shielding of the axis wiring harnesses and or seals in the machine ???
Results 1 to 25 of 205
Page 1 of 9 1 2 3 4