Search:

Tag: measured

Search: Search took 0.00 seconds.

    • Replies: 0
    • Views: 417
    Last Post: 04-26-2019 11:56 AM
    by Jarlemil  Go to last post

    Forum:
    Mazak

  1. Colchester 1600 Bantma mk2 threading issue.

    Started by griff25-06, 11-26-2018 04:15 AM
    • Replies: 7
    • Views: 424
    Last Post: 11-27-2018 05:15 PM
    by john.k  Go to last post

    Forum:
    General

  2. Doall vertical bandsaw alignment help needed!

    Started by Harri89, 10-13-2018 11:25 AM
    • Replies: 3
    • Views: 501
    Last Post: 10-13-2018 04:04 PM
    by jhruska  Go to last post

    Forum:
    General

  3. Determining Machine Taper - tl;dr Bolded

    Started by KevinPartner, 08-11-2018 07:22 PM
    machine, measured, slightly, taper, tool
    • Replies: 3
    • Views: 579
    Last Post: 08-12-2018 05:14 AM
    by LKeithR  Go to last post

    Forum:
    General

  4. Hendey spindle runout, help needed

    Started by RCPDesigns, 10-17-2017 06:03 PM
    • Replies: 9
    • Views: 1,154
    Last Post: 03-02-2018 08:06 PM
    by RCPDesigns  Go to last post
  5. Lathe Threading Issue

    Started by evesdropper, 02-21-2018 02:00 PM
    • Replies: 18
    • Views: 1,733
    Last Post: 02-23-2018 09:03 AM
    by evesdropper  Go to last post

    Forum:
    General

  6. 113 rockwell surface finish info

    Started by reedeprintice, 08-31-2017 02:53 PM
    • Replies: 11
    • Views: 2,795
    Last Post: 09-07-2017 12:19 PM
    by reedeprintice  Go to last post
  7. Found a Bridgeport mill for sale.

    Started by Plant machinist, 04-20-2017 05:30 PM
    bridgeport, dial, etching, measured, nice
    • Replies: 5
    • Views: 1,492
    Last Post: 04-21-2017 09:16 AM
    by Plant machinist  Go to last post

    Forum:
    General

  8. SB 13" Saddle and Apron Clutch Thrust Bearings

    Started by 55pickup, 02-06-2017 07:07 PM
    • Replies: 6
    • Views: 2,349
    Last Post: 02-15-2017 09:43 PM
    by 55pickup  Go to last post
    • Replies: 3
    • Views: 749
    Last Post: 11-04-2016 04:27 PM
    by Milacron  Go to last post
  9. Trying To Cut A Groove And I'm Stumped

    Started by steve45, 08-31-2016 10:12 PM
    block, cut, gauge, groove, measured
    • Replies: 19
    • Views: 3,506
    Last Post: 10-12-2016 07:34 AM
    by gwilson  Go to last post

    Forum:
    General

    • Replies: 15
    • Views: 3,266
    Last Post: 07-04-2016 12:52 PM
    by hawkfan9  Go to last post
  10. Hardinge R8 Collet Info; from Hardinge

    Started by car2, 06-12-2016 03:46 AM
    collets, hardinge, measured, r-8, sizes
    • Replies: 4
    • Views: 2,005
    Last Post: 06-20-2016 09:42 PM
    by Courier250  Go to last post
    • Replies: 9
    • Views: 3,382
    Last Post: 04-15-2016 03:06 PM
    by johnb53405  Go to last post

    Forum:
    Metrology

  11. Questions on thread measurement

    Started by wyop, 04-07-2016 08:14 PM
    class, measured, mic, thread, wires
    • Replies: 19
    • Views: 3,667
    Last Post: 04-10-2016 10:54 AM
    by Gary E  Go to last post

    Forum:
    General

  12. FS; Titanium bar

    Started by metalmaster10, 12-07-2015 03:47 PM
    2 Pages
    1 2
    • Replies: 24
    • Views: 4,119
    Last Post: 01-25-2016 06:09 PM
    by Spencer in NH  Go to last post
  13. Measured for Transport - 1962

    Started by alskdjfhg, 12-15-2015 09:16 AM
    2 Pages
    1 2
    measured, transport
    • Replies: 23
    • Views: 3,958
    Last Post: 01-01-2016 03:46 PM
    by Firecracker  Go to last post
Results 1 to 17 of 17