Search:

Tag: plastics

Search: Search took 0.00 seconds.

    • Replies: 12
    • Views: 742
    Last Post: 03-08-2020 05:29 PM
    by surplusjohn  Go to last post

    Forum:
    General

  1. Plastics can make your coolant split?

    Started by Finegrain, 11-12-2019 08:22 AM
    coolant, oil, plastics, split, water
    • Replies: 5
    • Views: 1,254
    Last Post: 11-14-2019 08:06 PM
    by garyhlucas  Go to last post
  2. machining 3d printed plastics

    Started by NewtonPens, 08-10-2019 06:04 PM
    • Replies: 9
    • Views: 1,126
    Last Post: 08-13-2019 03:54 PM
    by mhajicek  Go to last post

    Forum:
    General

    • Replies: 4
    • Views: 970
    Last Post: 03-05-2019 11:53 AM
    by adama  Go to last post
    • Replies: 10
    • Views: 1,012
    Last Post: 11-02-2018 03:35 PM
    by DanielG  Go to last post

    Forum:
    General

  3. FS: Ripper End mill 20mm

    Started by tcncj, 09-01-2018 03:34 PM
    20mm, aluminum, hours, plastics, ripper
    • Replies: 0
    • Views: 602
    Last Post: 09-01-2018 03:34 PM
    by tcncj  Go to last post
  4. Radial land endmills on thin walled plastics

    Started by Deylan, 02-10-2018 04:18 PM
    chatter, deep, endmills, plastics, pocket
    • Replies: 5
    • Views: 1,082
    Last Post: 02-11-2018 05:05 PM
    by michiganbuck  Go to last post
  5. Power constants for plastics?

    Started by Generic Default, 02-21-2017 10:14 PM
    • Replies: 9
    • Views: 1,400
    Last Post: 02-23-2017 12:06 PM
    by DMF_TomB  Go to last post

    Forum:
    General

  6. High temp lightweight plastics

    Started by psandherr, 12-18-2016 01:22 PM
    2 Pages
    1 2
    muffler, mufflers, plastic, plastics, racing
    • Replies: 20
    • Views: 2,487
    Last Post: 12-20-2016 04:43 AM
    by adama  Go to last post

    Forum:
    General

  7. Extruded Delrin / Acetal ?

    Started by Edster, 11-14-2016 04:52 PM
    cut, delrin, machine, plastics, sheet
    • Replies: 15
    • Views: 5,035
    Last Post: 11-16-2016 07:29 AM
    by EndlessWaltz  Go to last post
  8. what to do with thermoplastics drops?

    Started by TheCook, 10-05-2016 03:36 PM
    dealers, expensive, pieces, plastics, smaller
    • Replies: 4
    • Views: 1,476
    Last Post: 10-08-2016 02:50 AM
    by EPAIII  Go to last post

    Forum:
    General

  9. Can you recommend a stiff and chemical-resistant plastic?

    Started by abollman, 07-22-2016 05:05 PM
    2 Pages
    1 2
    machine, material, plastics, solvents, stiff
    • Replies: 26
    • Views: 2,942
    Last Post: 07-24-2016 12:46 PM
    by specfab  Go to last post

    Forum:
    General

  10. H7 reaming in plastics to pressfit bearings?

    Started by pawanmj, 05-08-2016 10:59 AM
    bearings, housing, plastics, pressfit, reaming
    • Replies: 6
    • Views: 2,519
    Last Post: 05-09-2016 10:13 PM
    by Conrad Hoffman  Go to last post

    Forum:
    General

  11. Cheap sources for plastics

    Started by rhoward, 01-07-2016 01:46 AM
    buy, full, plastics, rod, stock
    • Replies: 4
    • Views: 1,073
    Last Post: 01-07-2016 05:37 AM
    by Mike1974  Go to last post

    Forum:
    General

  12. Tivar 1000, anybody use it?

    Started by rons, 12-23-2015 09:28 PM
    • Replies: 1
    • Views: 1,251
    Last Post: 12-23-2015 09:40 PM
    by Stihl290  Go to last post

    Forum:
    General

  13. PTFE sheet machining guidance and handbook

    Started by aerobharath, 06-04-2015 06:23 AM
    machining, plastics, ptfe
    • Replies: 3
    • Views: 3,129
    Last Post: 06-04-2015 10:00 AM
    by specfab  Go to last post
    • Replies: 14
    • Views: 29,201
    Last Post: 05-31-2014 08:18 AM
    by DMF_TomB  Go to last post
Results 1 to 17 of 17