Search:

Tag: tenths

Search: Search took 0.00 seconds.

  1. How to make a reamer cut a little smaller?

    Started by Terry Keeley, 06-16-2019 09:54 AM
    3 Pages
    1 2 3
    1/16, cut, pins, reamer, tenths
    • Replies: 52
    • Views: 4,816
    Last Post: 06-21-2019 09:11 AM
    by AARONT  Go to last post

    Forum:
    General

  2. Turning 1018 Steel

    Started by Circuit 1, 10-12-2018 10:59 AM
    2 Pages
    1 2
    aluminum, feeds, lathe, speeds, tenths
    • Replies: 20
    • Views: 2,215
    Last Post: 10-17-2018 07:32 AM
    by Dualkit  Go to last post

    Forum:
    Mazak

  3. Need accurate location of a hole at a 30 degree angle

    Started by Conrad Hoffman, 05-25-2018 11:39 AM
    2 Pages
    1 2
    drill, hole, killer, location, tenths
    • Replies: 28
    • Views: 4,438
    Last Post: 06-07-2018 01:30 PM
    by Joe.cmspin  Go to last post

    Forum:
    General

  4. Scraping v- block

    Started by lucky7, 03-14-2018 02:48 PM
    90deg, angles, scraping, sine, tenths
    • Replies: 5
    • Views: 1,195
    Last Post: 03-14-2018 11:05 PM
    by TGTool  Go to last post
  5. More spindle runout

    Started by jdholbrook33, 02-20-2018 08:07 AM
    checked, put, spindle, tenths, tir
    • Replies: 8
    • Views: 990
    Last Post: 02-22-2018 08:53 AM
    by Rockyr49  Go to last post
  6. Starret 82B bore gages - any good ?

    Started by AlexO, 01-16-2018 03:49 PM
    8/10/12/14mm, bank, braking, holes, tenths
    • Replies: 15
    • Views: 1,081
    Last Post: 01-18-2018 05:44 PM
    by AlexO  Go to last post

    Forum:
    General

  7. Truing a 5c Collect Chuck with a D1-6 Mount

    Started by David_M, 08-29-2017 08:08 PM
    run-out, shows, tenths, thousandths, video
    • Replies: 3
    • Views: 1,135
    Last Post: 08-31-2017 07:23 PM
    by David_M  Go to last post

    Forum:
    General

    • Replies: 4
    • Views: 1,808
    Last Post: 12-14-2016 08:54 AM
    by SteveM  Go to last post
  8. Addendum to the “Hitting tenths on a lathe” thread

    Started by sneed, 05-05-2016 09:57 AM
    3 Pages
    1 2 3
    bore, mike, question, tenths, work
    • Replies: 43
    • Views: 5,796
    Last Post: 09-01-2016 01:44 AM
    by SAG 180  Go to last post

    Forum:
    General

  9. Grinding a magnetic chuck

    Started by ow2knives, 07-05-2016 06:50 PM
    2 Pages
    1 2
    • Replies: 36
    • Views: 7,307
    Last Post: 07-24-2016 09:09 AM
    by adama  Go to last post
    • Replies: 6
    • Views: 1,713
    Last Post: 07-14-2016 11:54 AM
    by kevin66  Go to last post
  10. Criterion "tenths" shaft help

    Started by bradhe, 06-14-2016 02:10 PM
    • Replies: 0
    • Views: 807
    Last Post: 06-14-2016 02:10 PM
    by bradhe  Go to last post

    Forum:
    General

  11. how do you say ".0127 mm"?

    Started by Joe Miranda, 01-21-2016 08:53 AM
    3 Pages
    1 2 3
    call, half, tenths, thou
    • Replies: 41
    • Views: 5,293
    Last Post: 01-23-2016 12:02 PM
    by hanermo  Go to last post

    Forum:
    General

Results 1 to 13 of 13