Search:

Tag: thread

Page 1 of 43 1 2 3 4

Search: Search took 0.01 seconds.

    • Replies: 10
    • Views: 261
    Last Post: 09-23-2020 01:58 PM
    by EmanuelGoldstein  Go to last post
    • Replies: 5
    • Views: 275
    Last Post: 09-23-2020 08:53 AM
    by Peter from Holland  Go to last post

    Forum:
    General

  1. ISO Photo of Merlin V12 Machinist Setup

    Started by JLeather, 09-22-2020 03:42 PM
    merlin, photo, thread, v12, years
    • Replies: 2
    • Views: 343
    Last Post: 09-23-2020 08:35 AM
    by JLeather  Go to last post
  2. Steve Watkins's Shop....

    Started by swatkins, 04-09-2020 02:08 PM
    3 Pages
    1 2 3
    • Replies: 44
    • Views: 8,246
    Last Post: 09-22-2020 05:18 PM
    by sfriedberg  Go to last post
  3. Thread dial question.

    Started by home lathe user, 09-20-2020 09:33 PM
    • Replies: 12
    • Views: 508
    Last Post: 09-22-2020 03:06 PM
    by donie  Go to last post
    • Replies: 4
    • Views: 243
    Last Post: 09-22-2020 01:06 PM
    by c5h5nino  Go to last post
  4. Sticky Thread Sticky: Welcome to Heavy Iron

    Started by texasgunsmith, 09-18-2020 07:52 PM
    2 Pages
    1 2
    cal, heavy, iron, thread, topic
    • Replies: 36
    • Views: 1,290
    Last Post: 09-20-2020 06:07 PM
    by texasgunsmith  Go to last post
    • Replies: 13
    • Views: 896
    Last Post: 09-19-2020 02:33 AM
    by ChrisBruno  Go to last post

    Forum:
    General

    • Replies: 35
    • Views: 1,161
    Last Post: 09-18-2020 10:55 AM
    by Tyrone Shoelaces  Go to last post
    • Replies: 0
    • Views: 133
    Last Post: 09-10-2020 03:59 PM
    by Glenn Brooks  Go to last post
  5. Getting Another South Bend 16x6 Operational

    Started by texasgunsmith, 03-26-2020 10:28 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 74
    • Views: 9,292
    Last Post: 09-09-2020 03:01 PM
    by texasgunsmith  Go to last post
  6. Threads were made today

    Started by Kevin T, 09-04-2020 08:10 PM
    2 Pages
    1 2
    • Replies: 30
    • Views: 1,560
    Last Post: 09-08-2020 12:42 AM
    by pavt  Go to last post
  7. [Doubt] Lathing threads for oilwell equipement

    Started by Bryan7, 09-03-2020 09:53 AM
    lathing, oil, problems, thread, threads
    • Replies: 2
    • Views: 444
    Last Post: 09-07-2020 01:38 PM
    by Bryan7  Go to last post

    Forum:
    General

    • Replies: 16
    • Views: 834
    Last Post: 09-04-2020 10:20 AM
    by Booze Daily  Go to last post

    Forum:
    General

    • Replies: 4
    • Views: 442
    Last Post: 08-31-2020 01:17 PM
    by tnmgcarbide  Go to last post

    Forum:
    General

  8. Identifying a Thread

    Started by RLRL, 08-27-2020 04:32 AM
    92.05mm, male, o.d, thread, type
    • Replies: 10
    • Views: 590
    Last Post: 08-28-2020 02:06 PM
    by kenton  Go to last post

    Forum:
    General

  9. Thread Pitch Error

    Started by Wjw159, 08-27-2020 07:31 AM
    error, thread, threads, tooth, tpi
    • Replies: 17
    • Views: 823
    Last Post: 08-28-2020 11:25 AM
    by rjs44032  Go to last post
  10. Help ID a taper pipe thread.

    Started by The Extractor, 08-27-2020 11:32 AM
    dia, fitting, hex, taper, thread
    • Replies: 13
    • Views: 542
    Last Post: 08-28-2020 09:58 AM
    by gregormarwick  Go to last post

    Forum:
    General

    • Replies: 22
    • Views: 2,521
    Last Post: 08-28-2020 07:35 AM
    by Milland  Go to last post

    Forum:
    General

  11. Cutting Wrong Thread Pitch SB9a

    Started by Wjw159, 08-26-2020 07:45 PM
    setup, thread, threads, tpi, wrong
    • Replies: 2
    • Views: 301
    Last Post: 08-27-2020 10:12 AM
    by BDRetz  Go to last post
  12. South Bend 9A Large dials

    Started by animal12, 08-23-2020 06:22 PM
    back, code, dials, large, thread
    • Replies: 2
    • Views: 403
    Last Post: 08-25-2020 11:10 AM
    by thagedorn  Go to last post
  13. Questions about my DV 59

    Started by mastuart, 02-13-2017 03:54 PM
    • Replies: 11
    • Views: 2,348
    Last Post: 08-22-2020 05:21 PM
    by Barry Stone  Go to last post
    • Replies: 11
    • Views: 794
    Last Post: 08-19-2020 01:19 PM
    by i_r_machinist  Go to last post

    Forum:
    General

  14. 21T - every G92 pass runs twice

    Started by gregormarwick, 08-19-2020 07:20 AM
    g92, machine, parameter, pass, thread
    • Replies: 2
    • Views: 317
    Last Post: 08-19-2020 11:02 AM
    by gregormarwick  Go to last post
  15. 4 jaw chuck purchase

    Started by hdkris, 08-18-2020 10:19 PM
    • Replies: 1
    • Views: 291
    Last Post: 08-19-2020 02:49 AM
    by thermite  Go to last post

    Forum:
    General

Results 1 to 25 of 1072
Page 1 of 43 1 2 3 4