Dynapath cnc MCP complete w/cabinet, console & servo amps *NE OHIO*
Close
Login to Your Account
Results 1 to 17 of 17
  1. #1
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default Dynapath cnc MCP complete w/cabinet, console & servo amps *NE OHIO*

























    Everything except motors, encoders, limit switches and spindle drive.


    $2000... will also consider trade of other machine shop or gunsmith related tooling and equipment . Pick up is preferred, but shipping can be arranged at buyers expense.
    Send P.M. if you're interested.

    Located 20 min east of Akron, Ohio

    This sale is for a complete dynapath cnc control package removed from a knee mill. It will include the manual, console, cabinet, D.C. power supply, servo amplifiers and everything else in the cabinet. It runs on 240v or 480v.

    The Dynapath system works great and has been trouble free since I purchased the mill earlier this year. The power supply was replaced with a new Mean Well unit sometime before I bought the mill.

    This machine came from a large, well known shop and appears to have been well maintained and seen very little use.

    I removed this control from service due to a glitchy X axis servo amplifier. When power is supplied to the amplifiers, all 3 amps power up fine. After roughly 45 seconds, the X axis board would shut down and the (temp/RMS) l.e.d. would be illuminated. This began to happen on about 70% of machine start-up's.

    I checked for shorts and could find none, I checked the DC supply voltage and it was fine. I swapped the boards around and the issue followed the board.

    I could no longer afford the downtime, so I replaced this control with a Centroid all-in-one-dc system. I already had this wired up in another cabinet, so I swapped out the whole unit.

    I took pictures and made notes of everything I had disconnected during removal which was kept to the bare minimum. I also tagged wires to provide the purchaser with an easier install. 3 pairs of db9 plugs will be included to provide you with a clean way to wire in your encoders.

    This control provided power to (3) Baldor 28 in/lb motors with 1000 line encoders which are not included with this sale.

    I will include 2 servo amplifiers I had saved from an old Anilam cnc system before it was scrapped. I'm not sure if they are interchangeable with the servo dynamics boards or not, but they're yours if you want them.

    The control has already been removed from the machine, but power can still be supplied to check basic computer functions in person if you'd like.

    Thank you for looking,

    - John

  2. #2
    Join Date
    Apr 2018
    Country
    UNITED STATES MINOR OUTLYING ISLANDS
    Posts
    7,084
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    3433

    Default

    Quote Originally Posted by Freedommachine View Post
    Thank you for looking,
    For anyone less than seventy, these came from Dynapath as a complete, integrated kit (with the motors, but I s'pose replacing with the same thing would be equivalent). They weren't some aftermarket mishmash of parts. And I understand Dynapath is still helpful and responsive, parts in stock, tech support and all that.

    Dynapath is a real control ....

  3. Likes GWIZ liked this post
  4. #3
    Join Date
    Jun 2006
    Location
    PA
    Posts
    601
    Post Thanks / Like
    Likes (Given)
    22
    Likes (Received)
    33

    Default

    Quote Originally Posted by EmanuelGoldstein View Post
    For anyone less than seventy, these came from Dynapath as a complete, integrated kit (with the motors, but I s'pose replacing with the same thing would be equivalent). They weren't some aftermarket mishmash of parts. And I understand Dynapath is still helpful and responsive, parts in stock, tech support and all that.

    Dynapath is a real control ....

    I agree...great units. I have two early 90's Dynapath Delta 20 controls still running strong in my shop.

  5. Likes GWIZ liked this post
  6. #4
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default

    It is a nice control and was kept in great condition as well. I debated just replacing the 1 glitchy servo amplifier with a new one from advanced motion controls.

    Like this: DPRALTR-025B200 Modbus RTU RS485 servo drive

    The older model AMC servo amps sell for half of what people are asking for ancient servo dynamics or glentek boards and are much more common.

    If I didn't already have the centroid control (full of proven programs and already defined tools), I certainly would've kept the dynapath.

    The 2 extra servo amps I will include were made by Westamp.

    Feel free to make me an offer. I would rather not list it on eBay but I will in another week or two.

    I will also include all (3) motor encoders and flex couplings for offers (cash/trade) close to my asking price.

    Trades of interest include, but are not limited to:

    • Rockwell hardness tester
    • Gage block set - not Chinese
    • Gage pin sets - not Chinese
    • Sine plate - not Chinese
    • Lista cabinet
    • (Nice) Kurt, Orange, GMT vises
    • Manual Bridgeport
    • Small heat treat oven- single phase- (Bar-z hot shot or similar)
    • Drill sharpener
    • decent surface grinder
    • D-bit grinder
    • Tooling (drills, taps, reamers, face mills, slab mills, slitting saws, ect)
    • Dial height gauge
    • 0.0001" test indicator
    • 0-6" depth mic
    • Chamber reamers
    • Headspace gauges
    • Surplus firearm parts, kits, mounts, tripods, ect.
    • Barrel blanks
    • (2) Argon tanks 120cf or larger
    • 3J collet chuck, indexer, rotary or stationary mill fixture.
    • Nice angle plate
    And probably much more!

  7. #5
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default

    $1600? I'd like to get this out of my shop before it starts snowing.

  8. #6
    Join Date
    Aug 2010
    Location
    Medina OH
    Posts
    2,343
    Post Thanks / Like
    Likes (Given)
    331
    Likes (Received)
    1150

    Default

    Can you PM me your phone number, I might know someone interested in buying.

    Thanks

  9. #7
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default

    PM sent, thank you!

  10. #8
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default

    This is still available. Anyone interested at $1400?

  11. #9
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default

    $1200. The cheapest cnc control package on the market.

    It comes with 2 spare Westamp servo amps and I will also include the encoders.

    Perfect for replacing an old worn out Anilam!

  12. #10
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default

    Anyone want to make an offer?

  13. #11
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default

    Anyone interested at $900?

  14. #12
    Join Date
    Aug 2010
    Location
    missouri, USA
    Posts
    321
    Post Thanks / Like
    Likes (Given)
    2
    Likes (Received)
    22

    Default

    That’s a great deal for someone, wish I were a little closer

  15. #13
    Join Date
    Feb 2014
    Location
    Southern Illinois University
    Posts
    78
    Post Thanks / Like
    Likes (Given)
    1
    Likes (Received)
    25

    Default

    Any manuals with it?

  16. #14
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default

    Quote Originally Posted by bastarddsm View Post
    Any manuals with it?
    I apologize for the delay. Yes, It will come with an operator manual as well as a few schematics. I have a maintenance manual from a vmc that ran a dynapath control, I'll throw that in as well. It covers some more in depth options on pic tables, how to configure the control for a tool changer, ect.

  17. #15
    Join Date
    Apr 2018
    Country
    UNITED STATES MINOR OUTLYING ISLANDS
    Posts
    7,084
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    3433

    Default

    I can't believe this is still out there .... Dynapath kicks ass for a simple milling machine or lathe. Professional, tested, decent support, straightforward, if I wuz going to do any kind of retro at all I'd snap this up in a heartbeat.

  18. #16
    Join Date
    Feb 2014
    Location
    Southern Illinois University
    Posts
    78
    Post Thanks / Like
    Likes (Given)
    1
    Likes (Received)
    25

    Default

    can you post a couple pictures of the toc of the maint manual? I'm interested in it to replace a dead control on one of a couple machines I have.

  19. #17
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Ohio
    Posts
    36
    Post Thanks / Like
    Likes (Given)
    6
    Likes (Received)
    14

    Default

    Quote Originally Posted by bastarddsm View Post
    can you post a couple pictures of the toc of the maint manual? I'm interested in it to replace a dead control on one of a couple machines I have.
    Sure. Could you send me an email? I'm on my phone and can't load pics directly to the site.


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •