FS: Kennedy Machinist Tool Chest parts (metal drawer pulls, dividers, slides)
Close
Login to Your Account
Likes Likes:  0
Results 1 to 11 of 11
  1. #1
    Join Date
    Nov 2006
    Location
    Southern California
    Posts
    1,064
    Post Thanks / Like
    Likes (Given)
    10
    Likes (Received)
    125

    Default FS: Kennedy Machinist Tool Chest parts (metal drawer pulls, dividers, slides)

    FS: Kennedy Machinist Toolbox parts

    Recently I realized I had way to many Kennedy tool boxes (like the one shown in the first photo) not being used quirreled away at home and at work. So I sold all but one off. Then I found a pile of spare parts I would never need. So here they are. Shipping not included. Probably US Post Office shipping will probably be the cheapest. US sales only.

    kennedy_520_tool_box.jpg


    A) 9 metal drawer pulls. Look to be cast metal. Probably came from a Model 520 tool box. Original these were swagged in place. The end of the mushroomed swage was drilled out for removal. I was planning on bottom tapping a 6-32 thread and screwing them in place with short pan head screws but never ended up needing them. Originally meant for 0.18" diameter holes with a 0.76" hole spacing, though you could modify that as needed. $21 for all

    img_6331.jpg

    B) 8 steel drawer dividers, not painted, all are 7.3" long, Heights are 0.62", 1.06" and 1.7", includes 8 metal springs to keep them in place from Pile F. Note some of the springs have surface rust. $11 for all

    img_6337.jpg

    C) 9 steel drawer dividers, green painted, all are 7.3" long, Heights are 0.62" and 1.65", includes 9 metal springs to keep them in place from Pile F. Note some of the springs have surface rust. $11 for all

    img_6339.jpg

    E) 4 aluminum drawer dividers, home made. all are 7.3" long, Heights are 0.81" and 1.5", with 4 Kennedy metal springs to keep them in place from Pile F. Note some of the springs have surface rust. $6 for all

    img_6334.jpg

  2. #2
    Join Date
    Nov 2006
    Location
    Southern California
    Posts
    1,064
    Post Thanks / Like
    Likes (Given)
    10
    Likes (Received)
    125

    Default

    F) Pile of spring clips for reference. I may have a couple spare.

    img_6335.jpg

    G) 12 metal drawer slides. There are the old style with the spring retainer clips built-in. They measure 7.6" x 0.67" x 0.32", All for $11

    img_6336.jpg

    Public Service Announcement: If your drawer slides do not pull smoothly, consider removing them and cleaning off the old oil or grease. Then rub the mating surfaces of the drawers, slides and box with block of paraffin wax. It makes a huge difference on reducing the pull force. Paraffin was also does not attract dirt like oil or grease. This technique also works well on similar Snap-On, Mac and Waterloo (who made tool boxes for a semi-defunct retailer who cannot be mentioned here) tool boxers and chests.

  3. #3
    Join Date
    Dec 2010
    Country
    UNITED STATES
    State/Province
    Pennsylvania
    Posts
    2,061
    Post Thanks / Like
    Likes (Given)
    30
    Likes (Received)
    283

    Default

    Are draw slides still available? I have similar Kennedy Box (3 of them) they look the same as the photo but have the center draw for Machinist Handbook. My slide measured 7.6" X .66" X .31"

  4. #4
    Join Date
    Nov 2006
    Location
    Southern California
    Posts
    1,064
    Post Thanks / Like
    Likes (Given)
    10
    Likes (Received)
    125

    Default

    Quote Originally Posted by Froneck View Post
    Are draw slides still available? I have similar Kennedy Box (3 of them) they look the same as the photo but have the center draw for Machinist Handbook. My slide measured 7.6" X .66" X .31"
    I still have the slides.

    The slide should fit. Sounds like you have Model 526, which is wider and has the center drawer. If you are interested, please PM me your mailing address asd I'll get the shipping cost.

  5. #5
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Alabama
    Posts
    2
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Do you still have the steel dividers?


    Sent from my iPhone using Tapatalk

  6. #6
    Join Date
    Nov 2006
    Location
    Southern California
    Posts
    1,064
    Post Thanks / Like
    Likes (Given)
    10
    Likes (Received)
    125

    Default

    Quote Originally Posted by JaredE View Post
    Do you still have the steel dividers?


    Sent from my iPhone using Tapatalk
    Yes, both sets of steel dividers are available. I will send you a private message thru Practical Machinist regarding the dividers.

  7. #7
    Join Date
    May 2020
    Country
    UNITED STATES
    State/Province
    Alabama
    Posts
    2
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Quote Originally Posted by crrmeyer View Post
    Yes, both sets of steel dividers are available. I will send you a private message thru Practical Machinist regarding the dividers.
    Messaged back. Thanks


    Sent from my iPhone using Tapatalk

  8. #8
    Join Date
    Jul 2020
    Country
    UNITED STATES
    State/Province
    Indiana
    Posts
    1
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Hi there, are the drawer pulls still available?

  9. #9
    Join Date
    Nov 2006
    Location
    Southern California
    Posts
    1,064
    Post Thanks / Like
    Likes (Given)
    10
    Likes (Received)
    125

    Default

    Yes, the drawer pulls are available. I'll send you a personal message thru this web site regarding.

    Thanks

  10. #10
    Join Date
    Jul 2020
    Country
    UNITED STATES
    State/Province
    Pennsylvania
    Posts
    1
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Hello, are any of the drawer dividers still available?

  11. #11
    Join Date
    Nov 2006
    Location
    Southern California
    Posts
    1,064
    Post Thanks / Like
    Likes (Given)
    10
    Likes (Received)
    125

    Default

    Quote Originally Posted by chuckclaywell View Post
    Hello, are any of the drawer dividers still available?
    I just had someone yesterday commit to buy an extra batch of dividers that I found. If that falls thru I will email you.

    I still have the metal handles for sale. In fact I found 8 more of them for 17 total.

    Thanks


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •