Large Parallels, Lathe Chuck, Hardinge Chucker Tool Holders, Rotary Table

jays68yak · Feb 1, 2020

I have a ton of stuff for sale that is excess.

-Brown and Sharpe 920 Parallel, $120 shipped
-Shop made large parallel, or at least from what I can tell. 4 sides appear to have been ground, 4"x2"x12" (54 pounds for the pair) $100 + shipping (might fit in a flat rate box)
-Shop made larger parallel, again from what I can tell. This pair has 5x 1/4-20 tapped holes on one side, with a counter sunk pair of holes. There are some kinks on the edges. These are 60 pounds each! 6"x2"x18" $160 for the pair plus shipping.
-Kurt D60 vise, no tag but cast in d60 on bottom. With handle. $200 plus shipping.
-Hardinge chucker tool holders. Only 5 of the c14 have hardinge on them. There are a few of the others that appear to be shop made but the bulk appear to be factory made just not marked? $350 shipped for the lot.
-8" 3 jaw chuck. Marked Poland PUTm-S8ZD No0023 78-. Several posts think this is a bison before they were known as bison. Have 2 keys as pictured. $250 shipped.
-Kenco 12" rotary table with fixture plate on top. $500 plus shipping.

Shipping some of the larger heavier stuff can happen but I mean it would be easier if you were local. I am open to offers.

jays68yak · Feb 1, 2020

More pictures

jays68yak · Feb 1, 2020

And More Pictures

jays68yak · Feb 1, 2020

Pictures of chuck

Mebfab · Feb 1, 2020

You are pretty much all sales. Read the rules about participating in the forum.

Dave Vincent · Feb 1, 2020

Hi,
I am interested in the B&S 920 parallels, but can't tell what size they are from the picture. Could you list the size.
Thanks Dave Vincent

Rob F. · Feb 1, 2020

Where in Ca are you?

jays68yak · Feb 1, 2020

Mebfab said:
You are pretty much all sales. Read the rules about participating in the forum.

Well I do have threads about my south bend lathe and Bridgeport. I'd post about my CNC but it's a home unit by a brand that isn't on here.

jays68yak · Feb 1, 2020

Dave Vincent said:
Hi,
I am interested in the B&S 920 parallels, but can't tell what size they are from the picture. Could you list the size.
Thanks Dave Vincent

It's only one of that one. 1.5*3*12

Rob F. said:
Where in Ca are you?

Gilroy 95020

Dave Vincent · Feb 2, 2020

Thanks But not the size I need.
Dave

Rob F. · Feb 4, 2020

Do you have any indication if the poland chuck is cast or forged? Or is there a max rpm on it?

jays68yak · Feb 4, 2020

Rob F. said:
Do you have any indication if the poland chuck is cast or forged? Or is there a max rpm on it?

I do not know for sure. I have not seen anything on it other then what I posted. I can pull the back off and see if it has any raw casting??

Rob F. · Feb 4, 2020

jays68yak said:
I do not know for sure. I have not seen anything on it other then what I posted. I can pull the back off and see if it has any raw casting??

Thank you, but only if it is easy.

Garwood · Feb 5, 2020

I have a Bison chuck identical to that one and it is cast.

jays68yak · Feb 5, 2020

Rob F. said:
Thank you, but only if it is easy.

My guess would be cast. The back plate is cast. It also needs to be cleaned out and regressed. It does move but that grease is dry and old.

Rob F. · Feb 6, 2020

jays68yak said:
My guess would be cast. The back plate is cast. It also needs to be cleaned out and regressed. It does move but that grease is dry and old.

Thanks for doing that, I have a cast cushman chuck that size and dont need a duplicate. It will go on a lathe with 3500 rpm max so I would like the chuck to be OK at good rpm. I have a small 5" for the max rpm's.

Large Parallels, Lathe Chuck, Hardinge Chucker Tool Holders, Rotary Table

Plastic

Attachments

Plastic

Attachments

Plastic

Attachments

Plastic

Attachments

Diamond

Cast Iron

Diamond

Plastic

Plastic

Cast Iron

Diamond

Plastic

Diamond

Diamond

Plastic

Attachments

Diamond

Similar threads